scholarly journals Low Voltage Time-Based Matrix Multiplier-and-Accumulator for Neural Computing System

Electronics ◽  
2020 ◽  
Vol 9 (12) ◽  
pp. 2138
Author(s):  
Sungjin Hong ◽  
Heechai Kang ◽  
Jusung Kim ◽  
Kunhee Cho
Keyword(s):  
Pulse Width ◽  
Low Voltage ◽  
Supply Voltage ◽  
Random Access ◽  
Computing System ◽  
Cmos Process ◽  
Neural Computing ◽  
Hardware Complexity ◽  
Input Size ◽  
Pulse Width Modulator

A time-based matrix multiply-and-accumulate (MAC) operation for a neural computing system is described. A simple and compact time-based matrix MAC structure is proposed that can perform multiplication and accumulation simultaneously in a single multiplier structure, and the hardware complexity is not affected by the matrix input size. To enhance the linearity of the weight factor, an offset-free pulse-width modulator is introduced. The proposed MAC architecture operates at a low supply voltage of 0.5 V while it consumes MAC energy of 0.38 pJ with a 32 nm low-power (LP) predictive technology model (PTM) CMOS process. In addition, the near-subthreshold operation can remove the level shifter to interface between the MAC operator and digital circuits such as static random-access-memory (SRAM) because both can utilize the same level of the supply voltage. The proposed MAC is based on a digital intensive pulse-width modulation, and thus it can further improve its performance and area with more advanced technologies.

Analysis of 6T SRAM Cell in Different Technologies

2017 ◽  
Vol MCSP2017 (01) ◽  
pp. 7-10 ◽  
Author(s):  
Subhashree Rath ◽  
Siba Kumar Panda
Keyword(s):  
Low Power ◽  
Data Storage ◽  
Low Voltage ◽  
Random Access ◽  
Storage Device ◽  
Cmos Process ◽  
Process Technology ◽  
Digital Devices ◽  
Noise Margin ◽  
Sram Cell

Static random access memory (SRAM) is an important component of embedded cache memory of handheld digital devices. SRAM has become major data storage device due to its large storage density and less time to access. Exponential growth of low power digital devices has raised the demand of low voltage low power SRAM. This paper presents design and implementation of 6T SRAM cell in 180 nm, 90 nm and 45 nm standard CMOS process technology. The simulation has been done in Cadence Virtuoso environment. The performance analysis of SRAM cell has been evaluated in terms of delay, power and static noise margin (SNM).

scholarly journals Design Strategies and Architectures for Ultra-Low-Voltage Delta-Sigma ADCs

Electronics ◽  
2021 ◽  
Vol 10 (10) ◽  
pp. 1156
Author(s):  
Lorenzo Benvenuti ◽  
Alessandro Catania ◽  
Giuseppe Manfredini ◽  
Andrea Ria ◽  
Massimo Piotto ◽  
...  
Keyword(s):  
Low Voltage ◽  
Flicker Noise ◽  
Supply Voltage ◽  
Cmos Process ◽  
Clock Frequency ◽  
Design Environment ◽  
Ultra Low Power ◽  
Analog Cmos ◽  
Gain Error ◽  
Dc Gain

The design of ultra-low voltage analog CMOS integrated circuits requires ad hoc solutions to counteract the severe limitations introduced by the reduced voltage headroom. A popular approach is represented by inverter-based topologies, which however may suffer from reduced finite DC gain, thus limiting the accuracy and the resolutions of pivotal circuits like analog-to-digital converters. In this work, we discuss the effects of finite DC gain on ultra-low voltage ΔΣ modulators, focusing on the converter gain error. We propose an ultra-low voltage, ultra-low power, inverter-based ΔΣ modulator with reduced finite-DC-gain sensitivity. The modulator employs a two-stage, high DC-gain, switched-capacitor integrator that applies a correlated double sampling technique for offset cancellation and flicker noise reduction; it also makes use of an amplifier that implements a novel common-mode stabilization loop. The modulator was designed with the UMC 0.18 μm CMOS process to operate with a supply voltage of 0.3 V. It was validated by means of electrical simulations using the CadenceTM design environment. The achieved SNDR was 73 dB, with a bandwidth of 640 Hz, and a clock frequency of 164 kHz, consuming only 200.5 nW. It achieves a Schreier Figure of Merit of 168.1 dB. The proposed modulator is also able to work with lower supply voltages down to 0.15 V with the same resolution and a lower power consumption despite of a lower bandwidth. These characteristics make this design very appealing in sensor interfaces powered by energy harvesting sources.

scholarly journals Investigation of PVT-Aware STT-MRAM Sensing Circuits for Low-VDD Scenario

Micromachines ◽  
2021 ◽  
Vol 12 (5) ◽  
pp. 551
Author(s):  
Zhongjian Bian ◽  
Xiaofeng Hong ◽  
Yanan Guo ◽  
Lirida Naviner ◽  
Wei Ge ◽  
...  
Keyword(s):  
Nonvolatile Memory ◽  
High Speed ◽  
Low Voltage ◽  
Supply Voltage ◽  
Random Access ◽  
Magnetic Tunnel Junction ◽  
Complementary Metal Oxide Semiconductor ◽  
Current Mode ◽  
Cmos Technology ◽  
Oxide Semiconductor

Spintronic based embedded magnetic random access memory (eMRAM) is becoming a foundry validated solution for the next-generation nonvolatile memory applications. The hybrid complementary metal-oxide-semiconductor (CMOS)/magnetic tunnel junction (MTJ) integration has been selected as a proper candidate for energy harvesting, area-constraint and energy-efficiency Internet of Things (IoT) systems-on-chips. Multi-VDD (low supply voltage) techniques were adopted to minimize energy dissipation in MRAM, at the cost of reduced writing/sensing speed and margin. Meanwhile, yield can be severely affected due to variations in process parameters. In this work, we conduct a thorough analysis of MRAM sensing margin and yield. We propose a current-mode sensing amplifier (CSA) named 1D high-sensing 1D margin, high 1D speed and 1D stability (HMSS-SA) with reconfigured reference path and pre-charge transistor. Process-voltage-temperature (PVT) aware analysis is performed based on an MTJ compact model and an industrial 28 nm CMOS technology, explicitly considering low-voltage (0.7 V), low tunneling magnetoresistance (TMR) (50%) and high temperature (85 °C) scenario as the worst sensing case. A case study takes a brief look at sensing circuits, which is applied to in-memory bit-wise computing. Simulation results indicate that the proposed high-sensing margin, high speed and stability sensing-sensing amplifier (HMSS-SA) achieves remarkable performance up to 2.5 GHz sensing frequency. At 0.65 V supply voltage, it can achieve 1 GHz operation frequency with only 0.3% failure rate.

scholarly journals A 0.3 V Rail-to-Rail Ultra-Low-Power OTA with Improved Bandwidth and Slew Rate

2021 ◽  
Vol 11 (2) ◽  
pp. 19
Author(s):  
Francesco Centurelli ◽  
Riccardo Della Sala ◽  
Pietro Monsurrò ◽  
Giuseppe Scotti ◽  
Alessandro Trifiletti
Keyword(s):  
Low Power ◽  
Low Voltage ◽  
Supply Voltage ◽  
Cmos Process ◽  
Slew Rate ◽  
Large Signal ◽  
Output Stage ◽  
Ultra Low Power ◽  
Input Stage ◽  
Rail To Rail

In this paper, we present a novel operational transconductance amplifier (OTA) topology based on a dual-path body-driven input stage that exploits a body-driven current mirror-active load and targets ultra-low-power (ULP) and ultra-low-voltage (ULV) applications, such as IoT or biomedical devices. The proposed OTA exhibits only one high-impedance node, and can therefore be compensated at the output stage, thus not requiring Miller compensation. The input stage ensures rail-to-rail input common-mode range, whereas the gate-driven output stage ensures both a high open-loop gain and an enhanced slew rate. The proposed amplifier was designed in an STMicroelectronics 130 nm CMOS process with a nominal supply voltage of only 0.3 V, and it achieved very good values for both the small-signal and large-signal Figures of Merit. Extensive PVT (process, supply voltage, and temperature) and mismatch simulations are reported to prove the robustness of the proposed amplifier.

Low-Power and Reference-Less Data and Clock Recovery Circuit for Visible Light Receivers

2018 ◽  
Author(s):  
Ming-Cheng Liu ◽  
Paul C.-P. Chao ◽  
Soh Sze Khiong
Keyword(s):  
Power Consumption ◽  
Low Power ◽  
Visible Light ◽  
Low Voltage ◽  
Supply Voltage ◽  
Clock And Data Recovery ◽  
Optical Receiver ◽  
Clock Recovery ◽  
Cmos Process ◽  
Rf Receiver

In this paper a low power all-digital clock and data recovery (ADCDR) with 1Mhz frequency has been proposed. The proposed circuit is designed for optical receiver circuit on the battery-less photovoltaic IoT (Internet of Things) tags. The conventional RF receiver has been replaced by the visible light optical receiver for battery-less IoT tags. With this proposed ADCDR a low voltage, low power consumption & tiny IoT tags can be fabricated. The proposed circuit achieve the maximum bandwidth of 1MHz, which is compatible with the commercial available LED and light sensor. The proposed circuit has been fabricated in TSMC 0.18um 1P6M standard CMOS process. Experimental results show that the power consumption of the optical receiver is approximately 5.58uW with a supply voltage of 1V and the data rate achieves 1Mbit/s. The lock time of the ADCDR is 0.893ms with 3.31ns RMS jitter period.

A 16.4 nW, Sub-1 V, Resistor-Less Voltage Reference with BJT Voltage Divider

2018 ◽  
Vol 27 (13) ◽  
pp. 1850206 ◽  
Author(s):  
Qingshan Yang ◽  
Peiqing Han ◽  
Niansong Mei ◽  
Zhaofeng Zhang
Keyword(s):  
Low Voltage ◽  
Supply Voltage ◽  
Voltage Divider ◽  
Total Power ◽  
Cmos Process ◽  
Operating Voltage ◽  
Voltage Reference ◽  
Ultra Low Power ◽  
Silicon Area ◽  
Total Power Consumption

A 16.4[Formula: see text]nW, sub-1[Formula: see text]V voltage reference for ultra-low power low voltage applications is proposed. This design reduces the operating voltage to 0.8[Formula: see text]V by a BJT voltage divider and decreases the silicon area considerably by eliminating resistors. The PTAT and CTAT are based on SCM structures and a scaled-down [Formula: see text], respectively, to improve the process insensitivity. This work is fabricated in 0.18[Formula: see text][Formula: see text]m CMOS process with a total area of 0.0033[Formula: see text]mm2. Measured results show that it works properly for supply voltage from 0.8[Formula: see text]V to 2[Formula: see text]V. The reference voltage is 467.2[Formula: see text]mV with standard deviation ([Formula: see text]) being 12.2 mV and measured TC at best is 38.7[Formula: see text]ppm/[Formula: see text]C ranging from [Formula: see text]C to 60[Formula: see text]C. The total power consumption is 16.4[Formula: see text]nW under the minimum supply voltage at 27[Formula: see text]C.

scholarly journals A 0.3 V PNN Based 10T SRAM with Pulse Control Based Read-Assist and Write Data-Aware Schemes for Low Power Applications

Sensors ◽  
2021 ◽  
Vol 21 (19) ◽  
pp. 6591
Author(s):  
Ming-Hwa Sheu ◽  
Chang-Ming Tsai ◽  
Ming-Yan Tsai ◽  
Shih-Chang Hsia ◽  
S. M. Salahuddin Morsalin ◽  
...  
Keyword(s):  
Low Power ◽  
Supply Voltage ◽  
Random Access ◽  
Average Energy ◽  
Cmos Process ◽  
Pulse Control ◽  
Power Performance ◽  
Process Technology ◽  
Low Leakage ◽  
Noise Margin

An innovative and stable PNN based 10-transistor (10T) static random-access memory (SRAM) architecture has been designed for low-power bit-cell operation and sub-threshold voltage applications. The proposed design belongs to the following features: (a) pulse control based read-assist circuit offers a dynamic read decoupling approach for eliminating the read interference; (b) we have utilized the write data-aware techniques to cut off the pull-down path; and (c) additional write current has enhanced the write capability during the operation. The proposed design not only solves the half-selected problems and increases the read static noise margin (RSNM) but also provides low leakage power performance. The designed architecture of 1-Kb SRAM macros (32 rows × 32 columns) has been implemented based on the TSMC-40 nm GP CMOS process technology. At 300 mV supply voltage and 10 MHz operating frequency, the read and write power consumption is 4.15 μW and 3.82 μW, while the average energy consumption is only 0.39 pJ.

scholarly journals Design techniques for low-voltage analog integrated circuits

2017 ◽  
Vol 68 (4) ◽  
pp. 245-255 ◽  
Author(s):  
Matej Rakús ◽  
Viera Stopjaková ◽  
Daniel Arbet
Keyword(s):  
Integrated Circuits ◽  
Low Voltage ◽  
Supply Voltage ◽  
Building Blocks ◽  
Cmos Process ◽  
Mos Transistors ◽  
Power Supply Voltage ◽  
Current Mirrors ◽  
Moderate Inversion ◽  
Design Techniques

AbstractIn this paper, a review and analysis of different design techniques for (ultra) low-voltage integrated circuits (IC) are performed. This analysis shows that the most suitable design methods for low-voltage analog IC design in a standard CMOS process include techniques using bulk-driven MOS transistors, dynamic threshold MOS transistors and MOS transistors operating in weak or moderate inversion regions. The main advantage of such techniques is that there is no need for any modification of standard CMOS structure or process. Basic circuit building blocks like differential amplifiers or current mirrors designed using these approaches are able to operate with the power supply voltage of 600 mV (or even lower), which is the key feature towards integrated systems for modern portable applications.

scholarly journals A 0.8 V 0.23 nW 1.5 ns Full-Swing Pass-Transistor XOR Gate in 130 nm CMOS

2013 ◽  
Vol 2013 ◽  
pp. 1-6 ◽  
Author(s):  
Nabihah Ahmad ◽  
Rezaul Hasan
Keyword(s):  
Circuit Design ◽  
Power Dissipation ◽  
Low Voltage ◽  
Supply Voltage ◽  
Propagation Delay ◽  
Cmos Process ◽  
Xor Gate ◽  
Power Efficient ◽  
Pass Transistor ◽  
Full Swing

A power efficient circuit topology is proposed to implement a low-voltage CMOS 2-input pass-transistor XOR gate. This design aims to minimize power dissipation and reduce transistor count while at the same time reducing the propagation delay. The XOR gate utilizes six transistors to achieve a compact circuit design and was fabricated using the 130 nm IBM CMOS process. The performance of the XOR circuit was validated against other XOR gate designs through simulations using the same 130 nm CMOS process. The area of the core circuit is only about 56 sq · µm with 1.5659 ns propagation delay and 0.2312 nW power dissipation at 0.8 V supply voltage. The proposed six-transistor implementation thus compares favorably with other existing XOR gate designs.

A 2.4 GHz Low Voltage Low Power Folded Down-Conversion Quadrature Mixer Design

2013 ◽  
Vol 760-762 ◽  
pp. 526-530
Author(s):  
Ming Li ◽  
Zhi Qun Li ◽  
Chen Jian Wu ◽  
Meng Zhang ◽  
Jia Cao ◽  
...  
Keyword(s):  
Low Voltage ◽  
Noise Figure ◽  
Supply Voltage ◽  
Cmos Process ◽  
Folded Structure ◽  
Single Side ◽  
Mixer Design ◽  
Low Supply Voltage ◽  
Single Side Band ◽  
Down Conversion

This paper introduces a 2.4 GHz down-conversion quadrature mixer which applied in the Wireless Sensor Network (WSN). The mixer uses a folded structure which is modified based on the conventional Gilbert mixer. It is designed in 0.18μm RF CMOS process with a low supply voltage of 1V. The post-simulation results show that the mixer achieves a conversion gain (CG) of 9.0dB, the input 1dB compression point (IP1dB) of-7.6dBm, the third-order input intercept point (IIP3) of 2.2dBm, and the single side-band (SSB) noise figure (NF) is 13.9dB. The mixer core consumes current about 1.2mA from a 1V power supply.

Sign in / Sign up

Export Citation Format

Share Document