scholarly journals Effects of H2S Loading Rate on the Performance of Reactive Absorption with Electrochemical Oxidation

2021 ◽  
Vol 11 (11) ◽  
pp. 4867
Author(s):  
Jeong-Hee Kang ◽  
JiHyeon Song ◽  
Hyonwook Ji ◽  
Sang-Leen Yun ◽  
Weonjae Kim ◽  
...  
Keyword(s):  
Numerical Model ◽  
Removal Rate ◽  
Water Solution ◽  
Order Kinetic ◽  
Transfer Coefficients ◽  
Electrolyzed Water ◽  
Reactive Absorption ◽  
Flexible Operation ◽  
Odorous Substances ◽  
Water Scrubber

The odor released from environmental facilities is recognized as a major problem in environmental industries. In this study, reactive absorption, using an electrolyzed water solution (electrolyzed water scrubber, EWS), was developed to treat the odorous gases H2S and NH3, which are representative odorous substances. In addition, a numerical model composed of mass transfer coefficients and zero-order kinetic constants was established to predict the performance of EWS. The model was verified through experiments and data fittings. In the experiments, the concentration of H2S varied from 500 to 2000 ppm, while NH3 was fixed at 500 ppm. The results revealed that the H2S removal rate varied depending on the inlet H2S concentration, but no changes were observed for NH3. The numerical model appropriately described the experimental results to further predict the performance of EWS. The model prediction results for the shock loading of H2S indicated that a 100% removal rate can be achieved by increasing the current density to 70 mA cm−2 or higher. Finally, the EWS can be used to reduce the odor, owing to its flexible operation that responds to fluctuating loading rates.

A Method for Estimating Mass Transfer Coefficients in a Packed Column Using Reactive Absorption Data

2005 ◽  
Vol 70 (3) ◽  
pp. 383-402
Author(s):  
Valery A. Danilov ◽  
Il Moon
Keyword(s):  
Experimental Data ◽  
Mass Transfer ◽  
Optimization Technique ◽  
Packed Column ◽  
Effective Area ◽  
Transfer Coefficients ◽  
Mass Transfer Coefficients ◽  
Model Calculations ◽  
Unit Model ◽  
Reactive Absorption

This paper is devoted to the development of a new method for estimating mass transfer coefficients and effective area in packed columns in the case of reactive absorption. The method is based on a plug-flow model of reactive absorption of carbon dioxide with sodium hydroxide solution. The parameter estimation problem is solved using an optimization technique. Some mass transfer parameters are found to be correlated. Global sensitivity analysis by Sobol's technique showed that the unit model with the defined objective function is sensitive to the estimated parameter. Case studies of reactive absorption with different packings illustrate application of the proposed method for estimating mass transfer coefficients and effective area from column operation data. The model calculations are compared with experimental data obtained by other authors. The concentration profiles calculated by the unit model with the estimated parameters are shown to match well with experimental profiles from literature. A good agreement between estimated values and experimental data from literature confirms the applicability of this method.

scholarly journals Pyrometallurgical Lithium-Ion-Battery Recycling: Approach to Limiting Lithium Slagging with the InduRed Reactor Concept

Processes ◽  
2021 ◽  
Vol 9 (1) ◽  
pp. 84
Author(s):  
Stefan Windisch-Kern ◽  
Alexandra Holzer ◽  
Christoph Ponak ◽  
Harald Raupenstrauch
Keyword(s):  
Removal Rate ◽  
Oxygen Affinity ◽  
Lithium Ion ◽  
Transfer Coefficients ◽  
Scanning Calorimetry ◽  
Recycling Industry ◽  
Reducing Conditions ◽  
Novel Approach ◽  
Input Material ◽  
High Oxygen Affinity

The complexity of the waste stream of spent lithium-ion batteries poses numerous challenges on the recycling industry. Pyrometallurgical recycling processes have a lot of benefits but are not able to recover lithium from the black matter since lithium is slagged due to its high oxygen affinity. The presented InduRed reactor concept might be a promising novel approach, since it does not have this disadvantage and is very flexible concerning the chemical composition of the input material. To prove its basic suitability for black matter processing, heating microscope experiments, thermogravimetric analysis and differential scanning calorimetry have been conducted to characterize the behavior of nickel rich cathode materials (LiNi0.8Co0.15Al0.05O2 and LiNi0.33Mn0.33Co0.33O2) as well as black matter from a pretreatment process under reducing conditions. Another experimental series in a lab scale InduRed reactor was further used to investigate achievable transfer coefficients for the metals of interest. The promising results show technically feasible reaction temperatures of 800 ∘C to 1000 ∘C and high recovery potentials for nickel, cobalt and manganese. Furthermore, the slagging of lithium was largely prevented and a lithium removal rate of up to 90% of its initial mass was achieved.

scholarly journals Lignocellulose@ Activated Clay Nanocomposite with Hierarchical Nanostructure Enhancing the Removal of Aqueous Zn(II)

Polymers ◽  
2019 ◽  
Vol 11 (10) ◽  
pp. 1710 ◽  
Author(s):  
Xiaotao Zhang ◽  
Yinan Hao ◽  
Zhangjing Chen ◽  
Yuhong An ◽  
Wanqi Zhang ◽  
...  
Keyword(s):  
Ph Value ◽  
Removal Rate ◽  
Weight Ratio ◽  
Order Kinetic ◽  
Adsorption Parameters ◽  
Hierarchical Nanostructure ◽  
Desorption Temperature ◽  
Desorption Time ◽  
Adsorption Temperature ◽  
Hcl Concentration

A lignocellulose@ activated clay (Ln@AC) nanocomposite with a hierarchical nanostructure was successfully synthesized by the chemical intercalation reaction and applied in the removal of Zn(II) from an aqueous solution. Ln@AC was characterized by N2 adsorption/desorption isotherms and X-Ray Diffraction (XRD), scanning Electron Microscope (SEM), transmission Electron Microscopy (TEM) and Fourier Transform Infrared Spectroscopy (FTIR) analysis, and the results indicate that an intercalated–exfoliated hierarchical nanostructure was formed. The effects of different adsorption parameters on the Zn(II) removal rate (weight ratio of Ln to AC, Ln@AC dosage, initial Zn(II) concentration, pH value, adsorption temperature, and time) were investigated in detail. The equilibrium adsorption capacity reached 315.9 mg/g under optimal conditions (i.e., the weight ratio of Ln to AC of 3:1, Ln@AC dosage of 1 g/L, initial Zn(II) concentration of 600 mg/L, pH value of 6.8, adsorption temperature of 65 °C, and adsorption time of 50 min). The adsorption process was described by the pseudo-second-order kinetic model, Langmuir isotherm model, and the Elovich model. Moreover, Zn(II) could be easily eluted by HCl, and the effects of HCl concentration, desorption temperature, and ultrasonic desorption time on desorbed amount were tested. Desorption studies revealed that with an HCl concentration of 0.25 mol/L, desorption temperature of 70 °C, and ultrasonic desorption time of 20 min, the maximum desorption capacity and efficiency were achieved at 202.5 mg/g and 64.10%, respectively. Regeneration experimental results indicated that the Ln@AC exhibited a certain recyclable regeneration performance. Due to such outstanding features, the novel Ln@AC nanocomposite proved to have great adsorption potential for Zn(II) removal from wastewater, and exhibited an extremely significant amount of adsorbed Zn(II) when compared to conventional adsorbents.

Preparation of Novel Ag–Si–TiO2 Composite and Research on Its Photocatalytic Degradation of Formaldehyde

2021 ◽  
Vol 13 (3) ◽  
pp. 371-380
Author(s):  
Yongjun Wu ◽  
Nina Xie ◽  
Lu Yu
Keyword(s):  
Photoelectron Spectroscopy ◽  
Removal Rate ◽  
Sol Gel ◽  
Catalytic Performance ◽  
Formaldehyde Concentration ◽  
Order Kinetic ◽  
Solution Ph ◽  
Visible Absorption ◽  
X Ray ◽  
Co Doped

A novel Ag–Si–TiO2 composite was prepared via sol–gel method for removing residual formaldehyde in shiitake mushroom. The structure of Ag–Si–TiO2 composite was characterized by scanning electron microscope (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) analyses. Ultraviolet-visible absorption spectroscopy (UV-Vis) and N2 adsorption-desorption tests showed that Ag and Si co-doped decreased the band gap, the Brunauer-Emmett-Teller (BET) specific surface area of the samples increased and the recombination probability of electron-hole pairs (e--h+) reduced. Effect on removal rate of formaldehyde with different Ag-Si co-doped content, formaldehyde concentration and solution pH were investigated, and the results showed that 6.0 wt%Ag-3.0 wt%Si-TiO2 samples had an optimum catalytic performance, and the degradation efficiency reached 96.6% after 40 W 365 nm UV lamp irradiation for 360 min. The kinetics of formaldehyde degradation by Ag–Si–TiO2 composite photocatalyst could be described by Langmuir-Hinshelwood first-order kinetic model.

scholarly journals Photoreduction of Cr(VI) Ions in Aqueous Solutions by UV/ Photocatalytic Processes

2012 ◽  
Vol 2012 ◽  
pp. 1-7 ◽  
Author(s):  
Chih Ming Ma ◽  
Yung Shuen Shen ◽  
Po Hsiang Lin
Keyword(s):  
Aqueous Solutions ◽  
Reaction Rate ◽  
Removal Rate ◽  
Experimental Results ◽  
Order Kinetic ◽  
Solution Ph ◽  
Relationship Of ◽  
The Relationship ◽  
Photocatalytic Processes ◽  
Order Kinetic Equation

This study discussed the photoreduction of Cr(VI) ions in aqueous solutions by UV/TiO2photocatalytic processes under various operational factors. Experimental results showed that the removal rate of Cr(VI) increased with decreasing solution pH values and with increasing dosages of organic compounds, indicating that the recombination rate of electrons and h+can be retarded in the reaction systems by the addition of the scavenger, thus raising the reaction rate of Cr(VI). The relationship of the chemical reaction rate of Cr(VI), TiO2dosage, and changes of Cr(VI) concentration was expressed by the pseudo-first-order kinetic equation. Comparing the experimental results of two different doping metals in modified TiO2photoreduction systems, the removal rate of Cr(VI) by the Ag/TiO2process is larger, possibly because the electron transferring ability of Ag is superior to that of Cu. However, the photoreduction rates of Cr(VI) by modified UV/TiO2processes are worse than those by a nonmodified commercial UV/TiO2process.

Nanoparticle Fe3O4 magnetized activated carbon from Armeniaca sibirica shell for the adsorption of Hg(II) ions

BioResources ◽  
2021 ◽  
Vol 16 (3) ◽  
pp. 6100-6120
Author(s):  
Yinan Hao ◽  
Yanfei Pan ◽  
Qingwei Du ◽  
Xudong Li ◽  
Ximing Wang
Keyword(s):  
Activated Carbon ◽  
Adsorption Capacity ◽  
Ph Value ◽  
Removal Rate ◽  
Freundlich Isotherm ◽  
Entropy Change ◽  
Isotherm Models ◽  
Order Kinetic ◽  
Adsorption Parameters ◽  
Initial Concentration

Armeniaca sibirica shell activated carbon (ASSAC) magnetized by nanoparticle Fe3O4 prepared from Armeniaca sibirica shell was investigated to determine its adsorption for Hg2+ from wastewater. Fe3O4/ASSAC was characterized using XRD (X-ray diffraction), FTIR (Fourier transform infrared spectroscopy), SEM (scanning electron microscopy), and BET (Brunauer–Emmett–Teller). Optimum adsorption parameters were determined based on the initial concentration of Hg2+, reaction time, reaction temperature, and pH value in adsorption studies. The experiment results demonstrated that the specific surface area of ASSAC decreased after magnetization; however the adsorption capacity and removal rate of Hg2+ increased 0.656 mg/g and 0.630%, respectively. When the initial concentration of Hg2+ solution was 250 mg/L and the pH value was 2, the adsorption time was 180 min and the temperature was 30 °C, and with the Fe3O4/ASSAC at 0.05 g, the adsorption reaching 97.1 mg/g, and the removal efficiency was 99.6%. The adsorption capacity of Fe3O4/ASSAC to Hg2+ was in accord with Freundlich isotherm models, and a pseudo-second-order kinetic equation was used to fit the adsorption best. The Gibbs free energy ΔGo < 0，enthalpy change ΔHo < 0, and entropy change ΔSo < 0 which manifested the adsorption was a spontaneous and exothermic process.

scholarly journals Preparation of grafting copolymer of acrylic acid onto loess surface and its adsorption behavior

2020 ◽  
Vol 82 (4) ◽  
pp. 673-682
Author(s):  
Fengqin Tang ◽  
Di Gao ◽  
Li Wang ◽  
Yufeng He ◽  
Pengfei Song ◽  
...  
Keyword(s):  
Acrylic Acid ◽  
Adsorption Capacity ◽  
Removal Rate ◽  
Vinyl Pyrrolidone ◽  
Mineral Particle ◽  
Gravimetric Analysis ◽  
Order Kinetic ◽  
Experimental Conditions ◽  
Order Kinetic Model ◽  
Grafting Copolymer

Abstract Loess is a typical natural mineral particle distributed widely around the world, and it is inexpensive, readily accessible, and harmless to the environment. In this study, loess was modified by surface grafting copolymerization of functional monomers, such as acrylic acid, N-vinyl pyrrolidone, and N,N-methylenebisacrylamide as a cross-linking agent, which afforded a novel loess-based grafting copolymer (LC-PAVP). After being characterized by scanning electron microscopy, thermal gravimetric analysis and Fourier-transform infrared spectroscopy, its adsorption capacity and mechanism of removing lead ions (Pb2+) were investigated. With the study of the optimal experimental conditions, it was demonstrated that the removal rate of Pb2+ by LC-PAVP can reach up to 99.49% in 60 min at room temperature. It was also found that the kinetic characteristics of the adsorption capacity due to the pseudo-second-order kinetic model and the thermodynamics conformed well with the Freundlich model. In summary, as a lost-cost and eco-friendly loess-based adsorbent, LC-PAVP is a good potential material for wastewater treatment.

Effect of Concentration on Electrospinning Oil Sorptive Fiber

2010 ◽  
Vol 160-162 ◽  
pp. 1611-1616
Author(s):  
Yan Ping Liu ◽  
Hua Bin Xu ◽  
Yi Bing Deng
Keyword(s):  
Fiber Diameter ◽  
Removal Rate ◽  
Electrospun Fiber ◽  
Scaling Law ◽  
Great Influence ◽  
Solution Concentration ◽  
Sorption Process ◽  
Processing Technique ◽  
Order Kinetic ◽  
Sorption Ability

Electrospinning is a convenient method used in the preparation of ultrafine oil sorptive fibers based on Ethylene-propylene-diene (EPDM), Electrospun fiber diameter, varying in large from micrometer to nanometer, mainly depends upon the solution concentration, which has great influence on this function fiber’s sorption ability. The non-linear relation between mean fiber diameter (d) and solution concentration (C) was investigated and it follows a simple scaling law in the form . This relationship can be used to predict the target fiber diameter and guide the processing technique. The effects of various C on oil sorption ability were investigated in a batch-sorption technique. A comparison of the kinetic models, showed that the removal rate fit the first order kinetic model well, which suggested the sorption process is rapid, can reach equilibrium within a short time.

Hybrid Ammonia Water Absorption System of Small and Medium Capacity

2003 ◽  
Author(s):  
Florea Chiriac ◽  
Robert Gavriliuc ◽  
Rodica Dumitrescu ◽  
Anica Ilie ◽  
Cristina Piˆrvu
Keyword(s):  
Water Solution ◽  
Electrical Energy ◽  
Cooling Capacity ◽  
Hot Water ◽  
Experimental Comparison ◽  
Maximum Temperature ◽  
Absorption System ◽  
Transfer Coefficients ◽  
Ammonia Water ◽  
Micro Channels

The paper presents an absorption system with compact heat exchangers (micro-channels), working with ammonia water solution, driven by either solar or electrical energy. The construction of the solar panels includes heat pipes, and they are able to provide hot water with a maximum temperature of 130°C. The cooling capacity of the system ranges from 5 to 10 kW. The system is designed for comfort the technological air conditioning, providing inside air temperatures in the range of 10°C to 20°C. The project promotes ammonia as an ecological and natural refrigerant and aims to experimentally evaluate the thermal performances of each component of the system (condenser, evaporator, absorber and vapor generator) and of the entire system. The next step consists in a theoretical versus experimental comparison of data. The thermal performances refer to heat transfer coefficients in micro-channels on water ammonia side, as well as on the airside, and to the performance coefficient for various working conditions.

Sign in / Sign up

Export Citation Format

Share Document