scholarly journals Design and Analysis of Three-Stage Amplifier for Driving pF-to-nF Capacitive Load Based on Local Q-Factor Control and Cascode Miller Compensation Techniques

Electronics ◽  
2019 ◽  
Vol 8 (5) ◽  
pp. 572 ◽  
Author(s):  
Qi Cheng ◽  
Weimin Li ◽  
Xian Tang ◽  
Jianping Guo
Keyword(s):  
Supply Voltage ◽  
Cmos Technology ◽  
Step Response ◽  
Phase Margin ◽  
Q Factor ◽  
Physical Size ◽  
Miller Compensation ◽  
Frequency Peak ◽  
Capacitive Load ◽  
Compensation Approach

This paper presents a new frequency compensation approach for three-stage amplifiers driving a pF-to-nF capacitive load. Thanks to the cascode Miller compensation, the non-dominant complex pole frequency is extended effectively, and the physical size of the compensation capacitors is also reduced. A local Q-factor control (LQC) loop is introduced to alter the Q-factor adaptively when loading capacitance CL varies significantly. This LQC loop decides how much damping current should be injected into the corresponding parasitic node to control the Q-factor of the complex-pole pair, which affects the frequency peak at the gain plot and the settling time of the proposed amplifier in the closed-loop step response. Additionally, a left-half-plane (LHP) zero is created to increase the phase margin and a feed-forward transconductance stage is paralleled to improve the slew rate (SR). Simulated in 0.13-µm CMOS technology, the amplifier is verified to handle a 4-pF-to-1.5-nF (375× drivability) capacitive load with at least 0.88-MHz gain-bandwidth (GBW) product and 42.3° phase margin (PM), while consuming 24.0-µW quiescent power at 1.0-V nominal supply voltage.

scholarly journals In-Pixel CTIA & Readout Circuitry for an Active CMOS Image Sensor

2021 ◽  
Vol 16 ◽  
pp. 626-632
Author(s):  
Aicha Menssouri ◽  
Karim El Khadiri ◽  
Ahmed Tahiri
Keyword(s):  
Supply Voltage ◽  
Cmos Image Sensor ◽  
Cmos Technology ◽  
Image Sensor ◽  
Transimpedance Amplifier ◽  
Phase Margin ◽  
Prior Work ◽  
Gain Margin ◽  
Pixel Circuit ◽  
Pixel Output

This work aims to design and simulate an in-pixel Capacitive Transimpedance Amplifier (CTIA) and peripheral circuitry that ensures pixel reading. Each pixel circuit is composed of four transistors using 90nm CMOS technology with a supply voltage of 1.8 V and is part of an array of pixels that make up a CMOS image sensor with peripheral circuitry. Pixel output is sent to a delta difference sampling (DDS) circuit to filter reset voltages. The Gain Margin achieved for the in-pixel CTIA is 44dB and 91dB for the Phase Margin. We also present measured pixel parameters and give a comparison with prior work. The timing and readout circuitry is also described.

High Gain and High CMRR Two-Stage Folded Cascode OTA with Nested Miller Compensation

2015 ◽  
Vol 24 (04) ◽  
pp. 1550057 ◽  
Author(s):  
Meysam Akbari ◽  
Omid Hashemipour
Keyword(s):  
Low Voltage ◽  
Supply Voltage ◽  
Cmos Technology ◽  
High Gain ◽  
Open Loop ◽  
Two Stage ◽  
Miller Compensation ◽  
Transconductance Amplifier ◽  
Dc Gain ◽  
Folded Cascode

By using Gm-C compensation (GCC) technique, a two-stage recycling folded cascode (FC) operational transconductance amplifier (OTA) is designed. The proposed configuration consists of recycling structure, positive feedback and feed-forward compensation path. In comparison with the typical folded cascode CMOS Miller amplifier, this design has higher DC gain, unity-gain frequency (UGF), slew rate and common mode rejection ratio (CMRR). The presented OTA is simulated in 0.18-μm CMOS technology and the simulation results confirm the theoretical analyses. Finally, the proposed amplifier has a 111 dB open-loop DC gain, 20 MHz UGF and 145 dB CMRR @ 1.2 V supply voltage while the power consumption is 400 μW which makes it suitable for low-voltage applications.

scholarly journals An 18.8–33.9 GHz, 2.26 mW Current-Reuse Injection-Locked Frequency Divider for Radar Sensor Applications

Sensors ◽  
2021 ◽  
Vol 21 (7) ◽  
pp. 2551
Author(s):  
Kwang-Il Oh ◽  
Goo-Han Ko ◽  
Jeong-Geun Kim ◽  
Donghyun Baek
Keyword(s):  
Supply Voltage ◽  
Cmos Technology ◽  
Frequency Divider ◽  
Oxide Semiconductor ◽  
Center Frequency ◽  
Radar Sensor ◽  
Frequency Locking ◽  
Current Reuse ◽  
Sensor Applications ◽  
Locking Range

An 18.8–33.9 GHz, 2.26 mW current-reuse (CR) injection-locked frequency divider (ILFD) for radar sensor applications is presented in this paper. A fourth-order resonator is designed using a transformer with a distributed inductor for wideband operating of the ILFD. The CR core is employed to reduce the power consumption compared to conventional cross-coupled pair ILFDs. The targeted input center frequency is 24 GHz for radar application. The self-oscillated frequency of the proposed CR-ILFD is 14.08 GHz. The input frequency locking range is from 18.8 to 33.8 GHz (57%) at an injection power of 0 dBm without a capacitor bank or varactors. The proposed CR-ILFD consumes 2.26 mW of power from a 1 V supply voltage. The entire die size is 0.75 mm × 0.45 mm. This CR-ILFD is implemented in a 65 nm complementary metal-oxide semiconductor (CMOS) technology.

scholarly journals Investigation of PVT-Aware STT-MRAM Sensing Circuits for Low-VDD Scenario

Micromachines ◽  
2021 ◽  
Vol 12 (5) ◽  
pp. 551
Author(s):  
Zhongjian Bian ◽  
Xiaofeng Hong ◽  
Yanan Guo ◽  
Lirida Naviner ◽  
Wei Ge ◽  
...  
Keyword(s):  
Nonvolatile Memory ◽  
High Speed ◽  
Low Voltage ◽  
Supply Voltage ◽  
Random Access ◽  
Magnetic Tunnel Junction ◽  
Complementary Metal Oxide Semiconductor ◽  
Current Mode ◽  
Cmos Technology ◽  
Oxide Semiconductor

Spintronic based embedded magnetic random access memory (eMRAM) is becoming a foundry validated solution for the next-generation nonvolatile memory applications. The hybrid complementary metal-oxide-semiconductor (CMOS)/magnetic tunnel junction (MTJ) integration has been selected as a proper candidate for energy harvesting, area-constraint and energy-efficiency Internet of Things (IoT) systems-on-chips. Multi-VDD (low supply voltage) techniques were adopted to minimize energy dissipation in MRAM, at the cost of reduced writing/sensing speed and margin. Meanwhile, yield can be severely affected due to variations in process parameters. In this work, we conduct a thorough analysis of MRAM sensing margin and yield. We propose a current-mode sensing amplifier (CSA) named 1D high-sensing 1D margin, high 1D speed and 1D stability (HMSS-SA) with reconfigured reference path and pre-charge transistor. Process-voltage-temperature (PVT) aware analysis is performed based on an MTJ compact model and an industrial 28 nm CMOS technology, explicitly considering low-voltage (0.7 V), low tunneling magnetoresistance (TMR) (50%) and high temperature (85 °C) scenario as the worst sensing case. A case study takes a brief look at sensing circuits, which is applied to in-memory bit-wise computing. Simulation results indicate that the proposed high-sensing margin, high speed and stability sensing-sensing amplifier (HMSS-SA) achieves remarkable performance up to 2.5 GHz sensing frequency. At 0.65 V supply voltage, it can achieve 1 GHz operation frequency with only 0.3% failure rate.

CMOS PULSE GENERATOR FOR BPSK, OOK, PAM, AND PPM MODULATIONS

2009 ◽  
Vol 18 (03) ◽  
pp. 487-495 ◽  
Author(s):  
VINCENZO STORNELLI ◽  
GIUSEPPE FERRI ◽  
KING PACE
Keyword(s):  
Remote Control ◽  
Power Consumption ◽  
Pulse Duration ◽  
Short Range ◽  
Pulse Generator ◽  
Supply Voltage ◽  
Pulse Repetition Frequency ◽  
Cmos Technology ◽  
Single Chip ◽  
Control Applications

This work presents a single chip integrated pulse generator-modulator to be utilized in a short range wireless radio sensors remote control applications. The circuit, which can generate single pulses, modulated in BPSK, OOK, PAM, and also PPM, has been developed in a standard CMOS technology (AMS 0.35 μm). Typical pulse duration is about 1 ns while pulse repetition frequency is until 200 MHz (5 ns "chip" time). The operating supply voltage is ± 2.5 V, while the whole power consumption is about 15 mW. Post-layout parametric and corner analyses have confirmed the theoretical expectations.

A 12-BIT 400-MS/s CURRENT-STEERING DAC WITH DEGLITCHING TECHNIQUE

2014 ◽  
Vol 23 (01) ◽  
pp. 1450004 ◽  
Author(s):  
XIAOBO XUE ◽  
XIAOLEI ZHU ◽  
QIFENG SHI ◽  
LENIAN HE
Keyword(s):  
Dynamic Range ◽  
Supply Voltage ◽  
Cmos Technology ◽  
Signal Frequency ◽  
Current Steering ◽  
Digital To Analog Converter ◽  
Measurement Results ◽  
Voltage Swing ◽  
Current Steering Dac ◽  
Low Supply Voltage

In this paper, a 12-bit current-steering digital-to-analog converter (DAC) employing a deglitching technique is proposed. The deglitching technique is realized by lowering the voltage swing of the control signal as well as by using a method of glitch counteraction (GC). A new switch–driver structure is designed to enable the effectiveness of the GC and provide sufficient driving capability under a low supply voltage. Moreover, the control signal's rise/fall asymmetry which increases the glitch error can be suppressed by using the proposed switch–driver structure. The 12-bit DAC is implemented in 180 nm CMOS technology. The measurement results show that the spurious free dynamic range (SFDR) at low signal frequency is 78.8 dB, and it is higher than 70 dB up to 60 MHz signal frequency at 400 MS/s. The measured INL and DNL are both less than ±0.6 LSB.

scholarly journals Low-voltage, low-power and high gain cmosota using active positive feedback with feed forward and FDCM techniques

2002 ◽  
Vol 15 (1) ◽  
pp. 93-101
Author(s):  
Lyes Bouzerara ◽  
Tahar Belaroussi ◽  
Boualem Amirouche
Keyword(s):  
Positive Feedback ◽  
Low Voltage ◽  
Supply Voltage ◽  
Phase Margin ◽  
Current Mirror ◽  
Power Supply Voltage ◽  
Gain Bandwidth ◽  
Frequency Dependent ◽  
Feed Forward ◽  
Current Mirrors

A low voltage, high dc gain and wideband load compensated cas code operational transconductance amplifier (OTA), using an active positive feedback with feed forward technique and frequency-dependent current mirrors (FDCM), is presented and analyzed. Such techniques stand as a powerful method of gain bandwidth and phase margin enhancements. In this paper, a frequency-dependent current mirror, whose input impedance increases with frequency, is used to form the feed forward path at the input of the current mirror with a feed forward capacitor. By using these techniques, the gain bandwidth product of the amplifier is improved from 115 MHz to 194 MHz, the phase margin is also improved from 85? to 95? and the gain is enhanced from 11 dB to 93 dB. This amplifier operates at 2.5 V power supply voltage drives a capacitive load of 1pF and gives a power dissipation of 7 mW. The predicted performance is verified by simulations using HSPICE tool with 0.8 fim CMOS AMS parameters.

scholarly journals Growth of high-quality semiconducting tellurium films for high-performance p-channel field-effect transistors with wafer-scale uniformity

2022 ◽  
Vol 6 (1) ◽  
Author(s):  
Taikyu Kim ◽  
Cheol Hee Choi ◽  
Pilgyu Byeon ◽  
Miso Lee ◽  
Aeran Song ◽  
...  
Keyword(s):  
Field Effect ◽  
Physical Vapor Deposition ◽  
High Performance ◽  
Supply Voltage ◽  
Field Effect Transistors ◽  
Low Cost ◽  
Three Dimensional ◽  
Cmos Technology ◽  
Oxide Semiconductor ◽  
Wafer Scale

AbstractAchieving high-performance p-type semiconductors has been considered one of the most challenging tasks for three-dimensional vertically integrated nanoelectronics. Although many candidates have been presented to date, the facile and scalable realization of high-mobility p-channel field-effect transistors (FETs) is still elusive. Here, we report a high-performance p-channel tellurium (Te) FET fabricated through physical vapor deposition at room temperature. A growth route involving Te deposition by sputtering, oxidation and subsequent reduction to an elemental Te film through alumina encapsulation allows the resulting p-channel FET to exhibit a high field-effect mobility of 30.9 cm2 V−1 s−1 and an ION/OFF ratio of 5.8 × 105 with 4-inch wafer-scale integrity on a SiO2/Si substrate. Complementary metal-oxide semiconductor (CMOS) inverters using In-Ga-Zn-O and 4-nm-thick Te channels show a remarkably high gain of ~75.2 and great noise margins at small supply voltage of 3 V. We believe that this low-cost and high-performance Te layer can pave the way for future CMOS technology enabling monolithic three-dimensional integration.

scholarly journals Design of area-efficient GHz range current mode frequency synthesizer using standard CMOS technology

2019 ◽  
Vol 70 (4) ◽  
pp. 323-328
Author(s):  
Dan-Dan Zheng ◽  
Yu-Bin Li ◽  
Chang-Qi Wang ◽  
Kai Huang ◽  
Xiao-Peng Yu
Keyword(s):  
Frequency Synthesizer ◽  
Frequency Tuning ◽  
Supply Voltage ◽  
Current Mode ◽  
Cmos Technology ◽  
Mode Frequency ◽  
Loop Filter ◽  
Silicon Area ◽  
Power Efficient ◽  
A Current

Abstract In this paper, an area and power efficient current mode frequency synthesizer for system-on-chip (SoC) is proposed. A current-mode transformer loop filter suitable for low supply voltage is implemented to remove the need of a large capacitor in the loop filter, and a current controlled oscillator with additional voltage based frequency tuning mechanism is designed with an active inductor. The proposed design is further integrated with a fully programmable frequency divider to maintain a good balance among output frequency operating range, power consumption as well as silicon area. A test chip is implemented in a standard 0.13 µm CMOS technology, measurement result demonstrates that the proposed design has a working range from 916 MHz to 1.1 l GHz and occupies a silicon area of 0.25 mm2 while consuming 8.4 mW from a 1.2 V supply.

scholarly journals Ladder-Based Synthesis and Design of Low-Frequency Buffer-Based CMOS Filters

Electronics ◽  
2021 ◽  
Vol 10 (23) ◽  
pp. 2931
Author(s):  
Waldemar Jendernalik ◽  
Jacek Jakusz ◽  
Grzegorz Blakiewicz
Keyword(s):  
Dynamic Range ◽  
Low Voltage ◽  
Supply Voltage ◽  
Low Frequency ◽  
Cmos Technology ◽  
Pass Filter ◽  
Low Pass Filter ◽  
Biomedical Sensors ◽  
Filter Synthesis ◽  
Cascade Method

Buffer-based CMOS filters are maximally simplified circuits containing as few transistors as possible. Their applications, among others, include nano to micro watt biomedical sensors that process physiological signals of frequencies from 0.01 Hz to about 3 kHz. The order of a buffer-based filter is not greater than two. Hence, to obtain higher-order filters, a cascade of second-order filters is constructed. In this paper, a more general method for buffer-based filter synthesis is developed and presented. The method uses RLC ladder prototypes to obtain filters of arbitrary orders. In addition, a set of novel circuit solutions with ultra-low voltage and power are proposed. The introduced circuits were synthesized and simulated using 180-nm CMOS technology of X-FAB. One of the designed circuits is a fourth-order, low-pass filter that features: 100-Hz passband, 0.4-V supply voltage, power consumption of less than 5 nW, and dynamic range above 60 dB. Moreover, the total capacitance of the proposed filter (31 pF) is 25% lower compared to the structure synthesized using a conventional cascade method (40 pF).

Sign in / Sign up

Export Citation Format

Share Document