scholarly journals Microstructural Evolution and Mechanical Properties of Hybrid Bevel Gears Manufactured by Tailored Forming

Metals ◽  
2020 ◽  
Vol 10 (10) ◽  
pp. 1365
Author(s):  
Bernd-Arno Behrens ◽  
Anna Chugreeva ◽  
Julian Diefenbach ◽  
Christoph Kahra ◽  
Sebastian Herbst ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Tensile Tests ◽  
The Novel ◽  
Bevel Gears ◽  
Processing Step ◽  
Near Net Shape ◽  
Manufacturing Technologies ◽  
Plasma Transferred Arc Welding ◽  
Tailored Forming ◽  
Processing Steps

The production of multi-metal bulk components requires suitable manufacturing technologies. On the example of hybrid bevel gears featuring two different steels at the outer surface and on the inside, the applicability of the novel manufacturing technology of Tailored Forming was investigated. In a first processing step, a semi-finished compound was manufactured by cladding a substrate using a plasma transferred arc welding or a laser hotwire process. The resulting semi-finished workpieces with a metallurgical bond were subsequently near-net shape forged to bevel gears. Using the residual heat after the forging process, a process-integrated heat treatment was carried out directly after forming. For the investigations, the material combinations of 41Cr4 with C22.8 (AISI 5140/AISI 1022M) and X45CrSi9-3 with C22.8 (AISI HNV3/AISI 1022M) were applied. To reveal the influence of the single processing steps on the resulting interface, metallographic examinations, hardness measurements and micro tensile tests were carried out after cladding, forging and process-integrated heat treatment. Due to forging and heat-treatment, recrystallization and grain refinement at the interface and an increase in both, hardness and tensile strength, were observed.

scholarly journals Tailored Forming of Hybrid Bevel Gears with Integrated Heat Treatment

2020 ◽  
Vol 47 ◽  
pp. 301-308 ◽  
Author(s):  
Bernd-Arno Behrens ◽  
Julian Diefenbach ◽  
Anna Chugreeva ◽  
Christoph Kahra ◽  
Sebastian Herbst ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Bevel Gears ◽  
Tailored Forming

scholarly journals Metallization of Thermoplastic Polymers and Composites 3D Printed by Fused Filament Fabrication

Technologies ◽  
2021 ◽  
Vol 9 (3) ◽  
pp. 49
Author(s):  
Alessia Romani ◽  
Andrea Mantelli ◽  
Paolo Tralli ◽  
Stefano Turri ◽  
Marinella Levi ◽  
...  
Keyword(s):  
Physical Vapor Deposition ◽  
Test Sample ◽  
Tensile Tests ◽  
Layer By Layer ◽  
Post Processing ◽  
Thermoplastic Polymers ◽  
Fused Filament Fabrication ◽  
Scanning Calorimetry ◽  
3D Printed ◽  
Manufacturing Technologies

Fused filament fabrication allows the direct manufacturing of customized and complex products although the layer-by-layer appearance of this process strongly affects the surface quality of the final parts. In recent years, an increasing number of post-processing treatments has been developed for the most used materials. Contrarily to other additive manufacturing technologies, metallization is not a common surface treatment for this process despite the increasing range of high-performing 3D printable materials. The objective of this work is to explore the use of physical vapor deposition sputtering for the chromium metallization of thermoplastic polymers and composites obtained by fused filament fabrication. The thermal and mechanical properties of five materials were firstly evaluated by means of differential scanning calorimetry and tensile tests. Meanwhile, a specific finishing torture test sample was designed and 3D printed to perform the metallization process and evaluate the finishing on different geometrical features. Furthermore, the roughness of the samples was measured before and after the metallization, and a cost analysis was performed to assess the cost-efficiency. To sum up, the metallization of five samples made with different materials was successfully achieved. Although some 3D printing defects worsened after the post-processing treatment, good homogeneity on the finest details was reached. These promising results may encourage further experimentations as well as the development of new applications, i.e., for the automotive and furniture fields.

scholarly journals Additive Manufacturing of Ti-Based Intermetallic Alloys: A Review and Conceptualization of a Next-Generation Machine

Materials ◽  
2021 ◽  
Vol 14 (15) ◽  
pp. 4317
Author(s):  
Thywill Cephas Dzogbewu ◽  
Willie Bouwer du Preez
Keyword(s):  
Heat Treatment ◽  
High Temperature ◽  
Additive Manufacturing ◽  
Complex Geometries ◽  
Intermetallic Alloys ◽  
Tial Alloys ◽  
Conventional Methods ◽  
Manufacturing Technologies ◽  
In Situ Heat Treatment

TiAl-based intermetallic alloys have come to the fore as the preferred alloys for high-temperature applications. Conventional methods (casting, forging, sheet forming, extrusion, etc.) have been applied to produce TiAl intermetallic alloys. However, the inherent limitations of conventional methods do not permit the production of the TiAl alloys with intricate geometries. Additive manufacturing technologies such as electron beam melting (EBM) and laser powder bed fusion (LPBF), were used to produce TiAl alloys with complex geometries. EBM technology can produce crack-free TiAl components but lacks geometrical accuracy. LPBF technology has great geometrical precision that could be used to produce TiAl alloys with tailored complex geometries, but cannot produce crack-free TiAl components. To satisfy the current industrial requirement of producing crack-free TiAl alloys with tailored geometries, the paper proposes a new heating model for the LPBF manufacturing process. The model could maintain even temperature between the solidified and subsequent layers, reducing temperature gradients (residual stress), which could eliminate crack formation. The new conceptualized model also opens a window for in situ heat treatment of the built samples to obtain the desired TiAl (γ-phase) and Ti3Al (α2-phase) intermetallic phases for high-temperature operations. In situ heat treatment would also improve the homogeneity of the microstructure of LPBF manufactured samples.

scholarly journals Effects of Different Solid Solution Temperatures on Microstructure and Mechanical Properties of the AA7075 Alloy After T6 Heat Treatment

2019 ◽  
Vol 38 (2019) ◽  
pp. 892-896 ◽  
Author(s):  
Süleyman Tekeli ◽  
Ijlal Simsek ◽  
Dogan Simsek ◽  
Dursun Ozyurek
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Solid Solution ◽  
Tensile Strength ◽  
Tensile Tests ◽  
Solution Temperature ◽  
T6 Heat Treatment ◽  
Microstructure And Mechanical Properties ◽  
Different Temperatures

AbstractIn this study, the effect of solid solution temperature on microstructure and mechanical properties of the AA7075 alloy after T6 heat treatment was investigated. Following solid solution at five different temperatures for 2 hours, the AA7075 alloy was quenched and then artificially aged at 120∘C for 24 hours. Hardness measurements, microstructure examinations (SEM+EDS, XRD) and tensile tests were carried out for the alloys. The results showed that the increased solid solution temperature led to formation of precipitates in the microstructures and thus caused higher hardness and tensile strength.

Hardening of Selective Laser Melted M2 Steel

2021 ◽  
Author(s):  
Mei Yang ◽  
Yishu Zhang ◽  
Haoxing You ◽  
Richard Smith ◽  
Richard D. Sisson
Keyword(s):  
Heat Treatment ◽  
High Speed ◽  
Cutting Tools ◽  
High Speed Steel ◽  
High Hardness ◽  
Steel Part ◽  
X Ray Diffraction ◽  
X Ray ◽  
Heat Treated ◽  
Near Net Shape

Abstract Selective laser melting (SLM) is an additive manufacturing technique that can be used to make the near-net-shape metal parts. M2 is a high-speed steel widely used in cutting tools, which is due to its high hardness of this steel. Conventionally, the hardening heat treatment process, including quenching and tempering, is conducted to achieve the high hardness for M2 wrought parts. It was debated if the hardening is needed for additively manufactured M2 parts. In the present work, the M2 steel part is fabricated by SLM. It is found that the hardness of as-fabricated M2 SLM parts is much lower than the hardened M2 wrought parts. The characterization was conducted including X-ray diffraction (XRD), optical microscopy, Scanning Electron Microscopy (SEM), and energy dispersive X-ray spectroscopy (EDS) to investigate the microstructure evolution of as-fabricated, quenched, and tempered M2 SLM part. The M2 wrought part was heat-treated simultaneously with the SLM part for comparison. It was found the hardness of M2 SLM part after heat treatment is increased and comparable to the wrought part. Both quenched and tempered M2 SLM and wrought parts have the same microstructure, while the size of the carbides in the wrought part is larger than that in the SLM part.

Influence of Heat Treatment on Microstructure and Mechanical Properties of Selective Laser Melted TiAl6V4 Alloy

2018 ◽  
Vol 284 ◽  
pp. 615-620 ◽  
Author(s):  
R.M. Baitimerov ◽  
P.A. Lykov ◽  
L.V. Radionova
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Selective Laser Melting ◽  
Room Temperature ◽  
Base Alloy ◽  
Tensile Tests ◽  
Heat Treatments ◽  
Laser Melting ◽  
Microstructure And Mechanical Properties ◽  
Treatment Procedures

TiAl6V4 titanium base alloy is widely used in aerospace and medical industries. Specimens for tensile tests from TiAl6V4 with porosity less than 0.5% was fabricated by selective laser melting (SLM). Specimens were treated using two heat treatment procedures, third batch of specimens was tested in as-fabricated statement after machining. Tensile tests were carried out at room temperature. Microstructure and mechanical properties of SLM fabricated TiAl6V4 after different heat treatments were investigated.

scholarly journals The Effect of Heat Treatment on the Microstructure and Mechanical Properties of the Novel Low-Cost Ti-3Al-5Mo-4Cr-2Zr-1Fe Alloy

Materials ◽  
2020 ◽  
Vol 13 (17) ◽  
pp. 3798
Author(s):  
Meng Sun ◽  
Dong Li ◽  
Yanhua Guo ◽  
Ying Wang ◽  
Yuecheng Dong ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Aging Time ◽  
Volume Fraction ◽  
Low Cost ◽  
Solution Treatment ◽  
Solution Temperature ◽  
The Novel ◽  
Α Phase ◽  
The Cost

In order to reduce the cost of titanium alloys, a novel low-cost Ti-3Al-5Mo-4Cr-2Zr-1Fe (Ti-35421) titanium alloy was developed. The influence of heat treatment on the microstructure characteristics and mechanical properties of the new alloy was investigated. The results showed that the microstructure of Ti-35421 alloy consists of a lamina primary α phase and a β phase after the solution treatment at the α + β region. After aging treatment, the secondary α phase precipitates in the β matrix. The precipitation of the secondary α phase is closely related to heat treatment parameters—the volume fraction and size of the secondary α phase increase when increasing the solution temperature or aging time. At the same solution temperature and aging time, the secondary α phase became coarser, and the fraction decreased with increasing aging temperature. When Ti-35421 alloy was solution-treated at the α + β region for 1 h with aging surpassing 8 h, the tensile strength, yield strength, elongation and reduction of the area were achieved in a range of 1172.7–1459.0 MPa, 1135.1–1355.5 MPa, 5.2–11.8%, and 7.5–32.5%, respectively. The novel low-cost Ti-35421 alloy maintains mechanical properties and reduces the cost of materials compared with Ti-3Al-5Mo-5V-4Cr-2Zr (Ti-B19) alloy.

Microstructural Effect and Material Homogenization of Thermal-Hydroforming Magnesium Alloy Tubes

2011 ◽  
Vol 465 ◽  
pp. 459-462 ◽  
Author(s):  
Lin Wang ◽  
Luen Chow Chan ◽  
Ting Fai Kong
Keyword(s):  
Heat Treatment ◽  
Magnesium Alloy ◽  
Tensile Tests ◽  
Heat Treatment Condition ◽  
Material Strength ◽  
Forming Process ◽  
Engineering Strain ◽  
Treatment Conditions ◽  
Metal Forming Process ◽  
Microstructural Effect

The microstrctural evolution pre and post heat treatment is critical to achieve a successful product for metal forming process. This paper aims to investigate the microstructual effect of the magnesium alloy tubes undergone various heat treatment conditions to achieve material homogenization. The heat treatment conditions under various periods of time (1, 2, 6, 12 and 30 hours) at 400 °C were employed to investigate the microstructural effect on hydroforming magnesium tubes. The greatly reduced impurity embedded in grain boundaries and more uniform grain sizes do indicate the improvement of material strength and ductility. To validate the conclusion, corresponding tensile tests at the different temperatures (20 °C and 200 °C) were carried out. The increased engineering strain in two directions (hoop and longitudinal) implies that the microstructural evolution is unquestionably useful to enhance the ductility of the magnesium tubes. Subsequently, the tubes after optimal heat treatment condition at 400 °C for 6 hours were used to further carry out the thermal hydroforming process for validation. The defect-free hydroformed tubes were produced under the same working condition, which is unable to be achieved for tubes without the heat-treatment process.

Synthesis of submicrometer-grained-ultrahigh-carbon steel containing 10% aluminum by ball-milling of powders

1996 ◽  
Vol 11 (11) ◽  
pp. 2725-2730 ◽  
Author(s):  
Eric M. Taleff ◽  
Mamoru Nagao ◽  
Yoshio Ashida ◽  
Oleg D. Sherby
Keyword(s):  
Grain Size ◽  
Ball Milling ◽  
Bulk Material ◽  
Hot Isostatic Pressing ◽  
High Strength ◽  
Tensile Tests ◽  
Grain Sizes ◽  
Ultrahigh Carbon Steel ◽  
Processing Step ◽  
Size Powder

An ultrahigh-carbon (1.25 wt.%) steel alloy containing 10 wt.% aluminum (UHCS–10Al) was processed by a powder metallurgy technique. Gas-atomized powders were subjected to ball-milling in an attritor in order to obtain a submicrometer grain size. Powder material was consolidated by both hot isostatic pressing (HIP) and by hot isopressure extrusion (HIE). Bulk material with submicrometer grain sizes was produced from attrited powders. The chemical composition and microstructure of this material are characterized at each processing step, from atomization through consolidation. Tensile tests show that a high strength results from the submicrometer grain size produced in the bulk material.

Sign in / Sign up

Export Citation Format

Share Document