scholarly journals Examination on Lightweight Banana Fibre (bunch) and Polyestercomposite for Industrial Applications

2019 ◽  
Vol 8 (4S2) ◽  
pp. 45-48 ◽  
Keyword(s):  
Polyester Resin ◽  
Resin Composite ◽  
Industrial Applications ◽  
Coconut Fiber ◽  
Banana Fiber ◽  
Strength Tests ◽  
Banana Fibre ◽  
Polymer Compound ◽  
The Impact ◽  
Disposal Problem

The durability of non-natural-reusable polymers is less identified, and it is challenging to dispose. To increase the durability and solve the disposal problem, polymers are reinforced with fibers. In this study, the banana fiber is used to prepare a lightweight composite mixed with a polymer compound. The fiber is extracted from the bunch of banana by retting process. The fabrication was done by adding fiber and the polyester resin in the mould by varying the composition, and the length of the fiber was fixed as 40 mm. As per standard of ASTM, The impact, tensile and flexural strength tests were conducted for the fabricated composite. The result was compared with coconut fiber and polyester resin composite. The study shows that the fiber prepared with the banana bunch shows a remarkable increase in mechanical properties proves to be a light weight material because of its less dense of fiber as 581 kg/m3. Hence, for industrial applications, the composite made of banana fiber and polyester can be used.

scholarly journals Effect of Al2O3 on the Tensile and Impact Strength of Flax/Unsaturated Polyester Composite with Emphasis on Automobile Body Applications

2021 ◽  
Vol 2021 ◽  
pp. 1-9
Author(s):  
Gebre Fenta Aynalem ◽  
Belete Sirahbizu
Keyword(s):  
Impact Strength ◽  
Polyester Resin ◽  
Natural Fiber ◽  
Resin Composite ◽  
Unsaturated Polyester ◽  
Fiber Material ◽  
Strength Properties ◽  
Unsaturated Polyester Resin ◽  
Molding Process ◽  
The Impact

This study has endeavored to develop an Al2O3-filled natural fiber reinforced polymer composite which is intended to substitute the most widely used synthetic E-glass fiber material. To attain the desired objective of the work, 0, 5, 10, and 15 wt% Al2O3-filled chopped flax/unsaturated polyester resin composite have been developed by the conventional hand-lay-up method followed by a compression molding process. Consequently, characterization and mechanical property tests are conducted based on the ASTM standard. The results revealed that both tensile and impact strength properties of the base chopped flax/unsaturated polyester resin composite are all affected due to the inclusion and variation of the content of Al2O3 in 15 and 25 wt% fiber loading cases. It has been noticed that a 39.06% increase in the ultimate tensile strength of the composite in 25/UPR-5 composition has been gained. The effect of Al2O3 on the impact strength of the base composite has also been analyzed and a 45% increase has been observed in 15/UPR-10 composition. The findings also witnessed that the newly developed composite can be applied to make automotive parts such as mud guard and engine undercover.

scholarly journals Mechanical characterization of polyester resin composite with natural fibers

2021 ◽  
pp. 17-23
Author(s):  
Carmen SALAZAR-HERNÁNDEZ ◽  
Juan Manuel MENDOZA-MIRANDA ◽  
Alfredo CORTES-LÓPEZ ◽  
Luis Fernando GONZÁLEZ-MÉNDEZ
Keyword(s):  
Polyester Resin ◽  
Mechanical Characterization ◽  
Brinell Hardness ◽  
Resin Composite ◽  
Natural Fibers ◽  
New Materials ◽  
Impact Simulation ◽  
The Matrix ◽  
The Impact

In this paper, composite materials reinforced with natural fibers were studied, such as: Jute (MC-RY) and Manta (MC-RM) as a proposal for new materials for the manufacture of a prototype for automotive defense. The materials were manufactured as laminates and characterized mechanically through stress, bending, impact and Brinell hardness index tests. The results indicated that both reinforcers improved the mechanical strength of the matrix by up to 71%, as well as the impact energy absorption by 14%. The mechanical properties for MC-RY determined in flexure (bending = 56 MPa, Eflection = 4.16 GPa and maximum = 14 mm) were used to perform an impact simulation in two different models created in SolidWork, the results indicated that the MC-RY could be used for the construction of the defense using 3 layers of this material.

scholarly journals Smoothing additive manufactured parts using ns-pulsed laser radiation

2021 ◽  
Author(s):  
Florian Kuisat ◽  
Fernando Lasagni ◽  
Andrés Fabián Lasagni
Keyword(s):  
Surface Roughness ◽  
Mechanical Performance ◽  
State Of The Art ◽  
Pulsed Laser ◽  
Industrial Applications ◽  
Laser Source ◽  
Pulsed Laser Radiation ◽  
Current State ◽  
The Impact

AbstractIt is well known that the surface topography of a part can affect its mechanical performance, which is typical in additive manufacturing. In this context, we report about the surface modification of additive manufactured components made of Titanium 64 (Ti64) and Scalmalloy®, using a pulsed laser, with the aim of reducing their surface roughness. In our experiments, a nanosecond-pulsed infrared laser source with variable pulse durations between 8 and 200 ns was applied. The impact of varying a large number of parameters on the surface quality of the smoothed areas was investigated. The results demonstrated a reduction of surface roughness Sa by more than 80% for Titanium 64 and by 65% for Scalmalloy® samples. This allows to extend the applicability of additive manufactured components beyond the current state of the art and break new ground for the application in various industrial applications such as in aerospace.

scholarly journals Oil and Flower Production in Rosa damascena trigintipetala Dieck under Salinity Stress in Taif Region, Saudi Arabia

2021 ◽  
Vol 13 (8) ◽  
pp. 4547
Author(s):  
Mohamed E. El-Sharnouby ◽  
Metwally M. Montaser ◽  
Sliai M. Abdallah
Keyword(s):  
Essential Oil ◽  
Essential Oils ◽  
Salinity Stress ◽  
Growth Parameters ◽  
Industrial Applications ◽  
Rosa Damascena ◽  
Flower Production ◽  
Survival Percentage ◽  
The Impact ◽  
Tolerance To Salinity

The flower industry depends on oil and fragrance, which is addressed in the current work. Different concentrations of NaCl (0, 250, 500, 1000, and 1500 ppm) were applied to Taif rose plants (Rosa damascena var. trigintipetala Dieck) to evaluate their effects on growth and essential oil content. Results clearly indicated the highest survival percentage (98.3%) was seen in untreated plants compared to plants under salinity stress. Moreover, increasing the NaCl levels induced an adverse effect on the growth parameters of Taif rose plants, while some essential oil contents were increased to the maximum degree of their tolerance to salinity stress. The extracted essential oils were analyzed using GC/MS. The essential oils of Taif rose plants treated with 500 ppm NaCl recorded the highest values of citronellol, geraniol and phenylethyl alcohol contents (16.56, 8.67 and 9.87%), respectively. NaCl at 250 ppm produced the highest values of heneicosane (13.12%), and then decreased to the lowest value (7.79%) with the increase of NaCl to 1500 NaCl, compared to the control and other NaCl levels. The current results could highlight the impact of salinity stress on Rosa damascena Miller var. trigintipetala Dieck for better economic and industrial applications.

scholarly journals Experimental studies on the possibility of using a pulsed laser for spot welding of thin metallic foils

2020 ◽  
Vol 10 (1) ◽  
pp. 674-680
Author(s):  
Piotr Sęk
Keyword(s):  
Experimental Studies ◽  
Pulsed Laser ◽  
Welding Process ◽  
Pulse Mode ◽  
Weld Strength ◽  
Spot Welds ◽  
Butt Welding ◽  
Strength Tests ◽  
Metallic Foils ◽  
The Impact

AbstractThe purpose of the experiment was to study the influence of the laser beam in pulse mode on metallic foils in order to obtain a spot weld. The welding process was carried out using the overlap weld method, using spot welds in various quantities. The Nd - YAG BLS 720 pulsed laser was used to conduct the experiment. The impact of the number of spot welds on the value of force needed to break the sample was examined. A number of measurements were carried out to determine the best process parameters. Butt welding and overlap welding were also performed using a continuous weld consisting of spot welds. Weld strength tests were performed to select the most appropriate parameters for the process under consideration.

scholarly journals Analysis of the Impact on the Mechanical Properties of Modification of Oligohydroxyethers in Organic Solvent Solution with Rubbers

Polymers ◽  
2021 ◽  
Vol 13 (4) ◽  
pp. 519
Author(s):  
Vitalii Bezgin ◽  
Agata Dudek ◽  
Adam Gnatowski
Keyword(s):  
Mechanical Properties ◽  
Scientific Paper ◽  
Styrene Butadiene Rubber ◽  
Butadiene Rubber ◽  
Molecular Weights ◽  
Wide Range ◽  
Strength Tests ◽  
Materials Used ◽  
Styrene Butadiene ◽  
The Impact

This paper proposes and presents the chemical modification of linear hydroxyethers (LHE) with different molecular weights (380, 640, and 1830 g/mol) with the addition of three types of rubbers (polysulfide rubber (PSR), polychloroprene rubber (PCR), and styrene-butadiene rubber (SBR)). The main purpose of choosing this type of modification and the materials used was the possibility to use it in industrial settings. The modification process was conducted for a very wide range of modifier additions (rubber) per 100 g LHE. The materials obtained in the study were subjected to strength tests in order to determine the effect of the modification on functional properties. Mechanical properties of the modified materials were improved after the application of the modifier (rubber) to polyhydroxyether (up to certain modifier content). The most favorable changes in the tested materials were registered in the modification of LHE-1830 with PSR. In the case of LHE-380 and LHE-640 modified in cyclohexanol (CH) and chloroform (CF) solutions, an increase in the values of the tested properties was also obtained, but to a lesser extent than for LHE-1830. The largest changes were registered for LHE-1830 with PSR in CH solution: from 12.1 to 15.3 MPa for compressive strength tests, from 0.8 to 1.5 MPa for tensile testing, from 0.8 to 14.7 MPa for shear strength, and from 1% to 6.5% for the maximum elongation. The analysis of the available literature showed that the modification proposed by the authors has not yet been presented in any previous scientific paper.

scholarly journals The impact of the health condition of oaks from the Krotoszyn Plateau on the mechanical properties of timber structures

2015 ◽  
Vol 57 (4) ◽  
pp. 224-232
Author(s):  
Jarosław Siwiński ◽  
Katarzyna Kubiak ◽  
Miłosz Tkaczyk ◽  
Anna Mazur ◽  
Ryszard Rekucki
Keyword(s):  
Mechanical Properties ◽  
Health Condition ◽  
Health State ◽  
Timber Structures ◽  
Strength Parameters ◽  
Modified Method ◽  
Strength Tests ◽  
Prior Selection ◽  
The Impact ◽  
Selection Of

Abstract The study was conducted to perform a comparative analysis of the mechanical properties of wood samples derived from oaks in the Krotoszyn Plateau, which depend on the health state of the trees. Strength parameters of oak wood were calculated for selected diseased and healthy trees (according to the Roloff classification). The study was conducted by a modified method described in the standard Polish Norm PN EN 408+ A1: 2012. For testing, prior selection of wood samples showed that more wood samples of diseased trees compared with those of healthy oaks did not fulfil the Polish standard requirements. According to the method used, the average results of strength tests of timber structures from healthy oaks exhibited higher strength parameters than those of the diseased trees.

Development of an End-Effector for Mitigation of Collisions

2021 ◽  
Author(s):  
Domenico Tommasino ◽  
Matteo Bottin ◽  
Giulio Cipriani ◽  
Alberto Doria ◽  
Giulio Rosati
Keyword(s):  
Numerical Simulations ◽  
Industrial Applications ◽  
Operating Conditions ◽  
Contact Forces ◽  
Design Parameters ◽  
End Effector ◽  
Linear Behavior ◽  
Stable Mechanism ◽  
Robot Tasks ◽  
The Impact

Abstract In robotics the risk of collisions is present both in industrial applications and in remote handling. If a collision occurs, the impact may damage both the robot and external equipment, which may result in successive imprecise robot tasks or line stops, reducing robot efficiency. As a result, appropriate collision avoidance algorithms should be used or, if it is not possible, the robot must be able to react to impacts reducing the contact forces. For this purpose, this paper focuses on the development of a special end-effector that can withstand impacts and is able to protect the robot from impulsive forces. The novel end-effector is based on a bi-stable mechanism that decouples the dynamics of the end-effector from the dynamics of the robot. The intrinsically non-linear behavior of the end-effector is investigated with the aid of numerical simulations. The effect of design parameters and the operating conditions are analyzed and the interaction between the functioning of the bi-stable mechanism and the control system is studied. In particular, the effect of the mechanism in different scenarios characterized by different robot velocities is shown. Results of numerical simulations assess the validity of the proposed end-effector, which can lead to large reductions in impact forces.

scholarly journals Effect of microwave disinfection on physical and mechanical properties of acrylic resins

2008 ◽  
Vol 19 (4) ◽  
pp. 348-353 ◽  
Author(s):  
Rafael Leonardo Xediek Consant ◽  
Erica Brenoe Vieira ◽  
Marcelo Ferraz Mesquita ◽  
Wilson Batista Mendes ◽  
João Neudenir Arioli-Filho
Keyword(s):  
Flexural Strength ◽  
Room Temperature ◽  
Physical And Mechanical Properties ◽  
Hardness Test ◽  
Knoop Hardness ◽  
Microwave Energy ◽  
Bending Test ◽  
Acrylic Resins ◽  
Strength Tests ◽  
The Impact

This study evaluated the effect of microwave energy on the hardness, impact strength and flexural strength of the Clássico, Onda-Cryl and QC-20 acrylic resins. Aluminum die were embedded in metallic or plastic flasks with type III dental stone, in accordance with the traditional packing technique. A mixing powder/liquid ratio was used according to the manufacturer's instructions. After polymerization in water batch at 74ºC for 9 h, boiling water for 20 min or microwave energy at 900 W for 10 min, the specimens were deflasked after flask cooling at room temperature, and submitted to finishing. Specimens non-disinfected and disinfected by microwave irradiation were submitted to hardness, impact and flexural strength tests. Each specimen was immersed in distilled water and disinfected in a microwave oven calibrated to 650 W for 3 min. Knoop hardness test was performed with 25 g load for 10 s, impact test was carried out using the Charpy system with 40 kpcm, and 3-point bending test with a crosshead speed of 0.5 mm/min until fracture. Data were submitted to statistical analysis by ANOVA and Tukey's test (?=0.05). Disinfection by microwave energy decreased the hardness of Clássico and Onda-Cryl acrylic resins, but no effect was observed on the impact and flexural strength of all tested resins.

scholarly journals A Comprehensive Review of Winding Short Circuit Fault and Irreversible Demagnetization Fault Detection in PM Type Machines

Energies ◽  
2018 ◽  
Vol 11 (12) ◽  
pp. 3309 ◽  
Author(s):  
Zia Ullah ◽  
Jin Hur
Keyword(s):  
Fault Diagnosis ◽  
Early Stage ◽  
Short Circuit ◽  
Industrial Applications ◽  
Operational Environment ◽  
Compact Structure ◽  
Torque Density ◽  
Prime Concern ◽  
Attractive Option ◽  
The Impact

Contemporary research has shown impetus in the diagnostics of permanent magnet (PM) type machines. The manufacturers are now more interested in building diagnostics features in the control algorithms of machines to make them more salable and reliable. A compact structure, exclusive high-power density, high torque density, and efficiency make the PM machine an attractive option to use in industrial applications. The impact of a harsh operational environment most often leads to faults in PM machines. The diagnosis and nipping of such faults at an early stage have appeared as the prime concern of manufacturers and end users. This paper reviews the recent advances in fault diagnosis techniques of the two most frequently occurring faults, namely inter-turn short fault (ITSF) and irreversible demagnetization fault (IDF). ITSF is associated with a short circuit in stator winding turns in the same phase of the machine, while IDF is associated with the weakening strength of the PM in the rotor. A detailed literature review of different categories of fault indexes and their strengths and weaknesses is presented. The research trends in the fault diagnosis and the shortcomings of available literature are discussed. Moreover, potential research directions and techniques applicable for possible solutions are also extensively suggested.

Sign in / Sign up

Export Citation Format

Share Document