scholarly journals Comparative Characterization of Hot-Pressed Polyamide 11 and 12: Mechanical, Thermal and Durability Properties

Polymers ◽  
2021 ◽  
Vol 13 (20) ◽  
pp. 3553
Author(s):  
Mohsen Bahrami ◽  
Juana Abenojar ◽  
Miguel Angel Martínez
Keyword(s):  
Mechanical Performance ◽  
Hardness Measurement ◽  
Tensile Tests ◽  
Point Of View ◽  
Scanning Calorimetry ◽  
Polyamide 11 ◽  
Small Water ◽  
Polyamide 12 ◽  
Durability Properties ◽  
Ductile Behavior

Chemically speaking, polyamide 11 (PA11) and polyamide 12 (PA12) have a similar backbone, differing only in one carbon. From an origin point of view, PA11 is considered a bioplastic polyamide composed from renewable resources, compared to oil-based PA12. Each of them has a number of advantages over the other, which makes their selection a challenging issue. Depending on the target application, diverse assessments and comparisons are needed to fulfill this mission. The current study addresses this research gap to characterize and compare PA11 and PA12 manufactured by the hot press technique in terms of their mechanical, thermal and durability properties for the first time, demonstrating their potential for future works as matrices in composite materials. In this regard, different characterization techniques are applied to the hot-pressed polymer sheets, including X-ray diffraction (XRD), differential scanning calorimetry (DSC), Fourier transform infrared spectroscopy (FTIR) and scanning electron microscopy (SEM). The mechanical performance of the PA11 and PA12 sheets is compared based on tensile tests and shore hardness measurement. The durability behavior of these two polyamides is evaluated in water and relative humidity conditions at different aging times. The experimental results show the ductile behavior of PA12 with respect to the quasi-brittle PA11. Both have a relatively small water and moisture gain: 1.5 wt% and 0.8 wt%, respectively. The higher crystallinity of PA12 (2.1 times more than PA11) with γ-phase is one of the leading parameters to achieve better mechanical and durability properties. The FTIR spectra displayed slight acid hydrolysis. Accordingly, absorbed water or moisture does not cause plasticization; thus, neither hardness nor dimension changes.

scholarly journals Wastes from Agricultural Silage Film Recycling Line as a Potential Polymer Materials

Polymers ◽  
2021 ◽  
Vol 13 (9) ◽  
pp. 1383
Author(s):  
Jerzy Korol ◽  
Aleksander Hejna ◽  
Klaudiusz Wypiór ◽  
Krzysztof Mijalski ◽  
Ewelina Chmielnicka
Keyword(s):  
Vinyl Acetate ◽  
Thermal Performance ◽  
Mechanical Performance ◽  
Ethylene Vinyl Acetate ◽  
Tensile Tests ◽  
Solid Particles ◽  
Polymer Materials ◽  
Slight Reduction ◽  
Scanning Calorimetry ◽  
Crystallinity Degree

The recycling of plastics is currently one of the most significant industrial challenges. Due to the enormous amounts of plastic wastes generated by various industry branches, it is essential to look for potential methods for their utilization. In the presented work, we investigated the recycling potential of wastes originated from the agricultural films recycling line. Their structure and properties were analyzed, and they were modified with 2.5 wt % of commercially available compatibilizers. The mechanical and thermal performance of modified wastes were evaluated by tensile tests, thermogravimetric analysis, and differential scanning calorimetry. It was found that incorporation of such a small amount of modifiers may overcome the drawbacks caused by the presence of impurities. The incorporation of maleic anhydride-grafted compounds enhanced the tensile strength of wastes by 13–25%. The use of more ductile compatibilizers—ethylene-vinyl acetate and paraffin increased the elongation at break by 55–64%. The presence of compatibilizers also reduced the stiffness of materials resulting from the presence of solid particles. It was particularly emphasized for styrene-ethylene-butadiene-styrene and ethylene-vinyl acetate copolymers, which caused up to a 20% drop of Young’s modulus. Such effects may facilitate the further applications of analyzed wastes, e.g., in polymer film production. Thermal performance was only slightly affected by compatibilization. It caused a slight reduction in polyethylene melting temperatures (up to 2.8 °C) and crystallinity degree (up to 16%). For more contaminated materials, the addition of compatibilizers caused a minor reduction in the decomposition onset (up to 6 °C). At the same time, for the waste after three washing cycles, thermal stability was improved. Moreover, depending on the desired properties and application, materials do not have to go through the whole recycling line, simplifying the process, reducing energy and water consumption. The presented results indicate that it is possible to efficiently use the materials, which do not have to undergo the whole recycling process. Despite the presence of impurities, they could be applied in the manufacturing of products which do not require exceptional mechanical performance.

scholarly journals Characterization of Beeswax, Candelilla Wax and Paraffin Wax for Coating Cheeses

Coatings ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 261
Author(s):  
Adolfo Bucio ◽  
Rosario Moreno-Tovar ◽  
Lauro Bucio ◽  
Jessica Espinosa-Dávila ◽  
Francisco Anguebes-Franceschi
Keyword(s):  
Physical And Mechanical Properties ◽  
Tensile Tests ◽  
Paraffin Wax ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
Absorption Bands ◽  
Dimensional Changes ◽  
Ductile Behavior ◽  
Candelilla Wax

A study on the physical and mechanical properties of beeswax (BW), candelilla wax (CW), paraffin wax (PW) and blends was carried out with the aim to evaluate their usefulness as coatings for cheeses. Waxes were analyzed by X-ray diffraction (XRD), Fourier Transform Infrared Spectroscopy (FTIR), differential scanning calorimetry (DSC), permeability, viscosity, flexural and tensile tests and scanning electron microscopy. Cheeses were coated with the waxes and stored for 5 weeks at 30 °C. Measured parameters were weight, moisture, occurrence and degree of fractures, and dimensional changes. The crystal phases identified by XRD for the three waxes allowed them to determine the length of alkanes and the nonlinear compounds in crystallizable forms in waxes. FTIR spectra showed absorption bands between 1800 and 800 cm−1 related to carbonyls in BW and CW. In DSC, the onset of melting temperature was 45.5 °C for BW, and >54 °C for CW and PW. Cheeses coated with BW did not show cracks after storage. Cheeses coated with CW and PW showed microcraks, and lost weight, moisture and shrunk. In the flexural and tensile tests, BW was ductile; CW and PW were brittle. BW blends with CW or PW displays a semi ductile behavior. Cheeses coated with BW blends lost less than 5% weight during storage. The best waxes were BW and the blends.

Influence of constituents and process parameters on mechanical properties of flax fibre-reinforced polyamide 11 composite

2016 ◽  
Vol 30 (11) ◽  
pp. 1503-1521 ◽  
Author(s):  
Yann Lebaupin ◽  
Michaël Chauvin ◽  
Thuy-Quynh Truong Hoang ◽  
Fabienne Touchard ◽  
Alexandre Beigbeder
Keyword(s):  
Process Parameters ◽  
Tensile Tests ◽  
Mechanical Analysis ◽  
Damping Factor ◽  
Hot Press ◽  
Scanning Calorimetry ◽  
Electron Microscopic ◽  
Polyamide 11 ◽  
Optimum Configuration ◽  
Scanning Electron Microscopic

Flax unidirectional (UD) fabrics and polyamide 11 (PA11) are used to create a 100% bio-sourced composite. The fabrication process is hot press moulding. Different configurations are studied by varying process parameters and composite constituents. Three temperature values (190°C, 200°C and 210°C) are combined with three pressure levels (35, 65 and 100 bars). In addition, two types of flax fabric (A and B) are tested and two types of PA11 (in the form of powder or film) are used. The two forms of PA11 are characterized using differential scanning calorimetry and rheological methods. Ten different composites are then manufactured. They are compared by means of tensile tests and dynamic mechanical analysis (DMA). Results are correlated with microstructural study: measurements of porosity degree and scanning electron microscopic observations are also performed. Finally, an optimum configuration is determined: the composite flax B/PA11 film manufactured with a temperature value of 210°C and using gradual levels of pressure (25 bars during 2 min, 40 bars during 2 min and 65 bars until the end of cycle). This configuration leads to a Young’s modulus value of 36 GPa and a tensile strength of 174 MPa, with the highest storage modulus and the lowest damping factor values measured by DMA.

Effect of liquid butadiene rubber on mechanical properties of polyamide 11/polyamide 12 blends

2015 ◽  
Vol 35 (4) ◽  
pp. 349-357 ◽  
Author(s):  
Jan Simek ◽  
Veronika Dockalova ◽  
Zdenek Hrdlicka ◽  
Vratislav Duchacek
Keyword(s):  
Impact Strength ◽  
Molar Mass ◽  
Mechanical Analysis ◽  
Butadiene Rubber ◽  
Scanning Calorimetry ◽  
Polyamide 11 ◽  
Polyamide 12 ◽  
End Groups ◽  
The Impact ◽  
Ubbelohde Viscometer

Abstract Polyamide 11 (PA 11)/polyamide 12 (PA 12) blends with and without liquid polybutadiene (LB) containing isocyanate end groups (LBD) were prepared in the Brabender plastograph. The rubber was added in order to increase the impact strength of the polyamides. Tensile strength and elongation at the upper yield point and hardness were also measured. Thermal properties were determined by differential scanning calorimetry (DSC) and dynamic mechanical analysis (DMA). Fourier transform infrared (FTIR) spectroscopy was used to determine functional groups of polyamides and to reveal possible reactions between the polyamides and LBD. Intrinsic viscosity, measured by an Ubbelohde viscometer, was used to calculate molar mass. The LB has been found as a useful modifier of impact strength.

scholarly journals Chemical and physical interactions of regenerated cellulose yarns and isocyanate-based matrix systems

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Bernhard Ungerer ◽  
Ulrich Müller ◽  
Antje Potthast ◽  
Enrique Herrero Acero ◽  
Stefan Veigel
Keyword(s):  
Mechanical Performance ◽  
Tensile Force ◽  
Tensile Modulus ◽  
Tensile Tests ◽  
Size Exclusion ◽  
Regenerated Cellulose ◽  
Hydrolytic Cleavage ◽  
Yarn Twist ◽  
Exclusion Chromatography ◽  
Physical And Chemical

AbstractIn the development of structural composites based on regenerated cellulose filaments, the physical and chemical interactions at the fibre-matrix interphase need to be fully understood. In the present study, continuous yarns and filaments of viscose (rayon) were treated with either polymeric diphenylmethane diisocyanate (pMDI) or a pMDI-based hardener for polyurethane resins. The effect of isocyanate treatment on mechanical yarn properties was evaluated in tensile tests. A significant decrease in tensile modulus, tensile force and elongation at break was found for treated samples. As revealed by size exclusion chromatography, isocyanate treatment resulted in a significantly reduced molecular weight of cellulose, presumably owing to hydrolytic cleavage caused by hydrochloric acid occurring as an impurity in pMDI. Yarn twist, fibre moisture content and, most significantly, the chemical composition of the isocyanate matrix were identified as critical process parameters strongly affecting the extent of reduction in mechanical performance. To cope with the problem of degradative reactions an additional step using calcium carbonate to trap hydrogen ions is proposed.

scholarly journals Is Micro X-ray Computer Tomography a Suitable Non-Destructive Method for the Characterisation of Dental Materials?

Polymers ◽  
2021 ◽  
Vol 13 (8) ◽  
pp. 1271
Author(s):  
Andreas Koenig ◽  
Leonie Schmohl ◽  
Johannes Scheffler ◽  
Florian Fuchs ◽  
Michaela Schulz-Siegmund ◽  
...  
Keyword(s):  
Flexural Strength ◽  
Computer Tomography ◽  
Mechanical Performance ◽  
Dental Materials ◽  
Three Dimensional ◽  
X Rays ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Multiple Measurements ◽  
High Doses

The aim of the study was to investigate the effect of X-rays used in micro X-ray computer tomography (µXCT) on the mechanical performance and microstructure of a variety of dental materials. Standardised bending beams (2 × 2 × 25 mm3) were forwarded to irradiation with an industrial tomograph. Using three-dimensional datasets, the porosity of the materials was quantified and flexural strength was investigated prior to and after irradiation. The thermal properties of irradiated and unirradiated materials were analysed and compared by means of differential scanning calorimetry (DSC). Single µXCT measurements led to a significant decrease in flexural strength of polycarbonate with acrylnitril-butadien-styrol (PC-ABS). No significant influence in flexural strength was identified for resin-based composites (RBCs), poly(methyl methacrylate) (PMMA), and zinc phosphate cement (HAR) after a single irradiation by measurement. However, DSC results suggest that changes in the microstructure of PMMA are possible with increasing radiation doses (multiple measurements, longer measurements, higher output power from the X-ray tube). In summary, it must be assumed that X-ray radiation during µXCT measurement at high doses can lead to changes in the structure and properties of certain polymers.

scholarly journals Mechanical Optimization of Concrete with Recycled PET Fibres Based on a Statistical-Experimental Study

Materials ◽  
2021 ◽  
Vol 14 (2) ◽  
pp. 240
Author(s):  
Alejandro Meza ◽  
Pablo Pujadas ◽  
Laura Montserrat Meza ◽  
Francesc Pardo-Bosch ◽  
Rubén D. López-Carreño
Keyword(s):  
Reinforced Concrete ◽  
Aspect Ratio ◽  
Mechanical Performance ◽  
Tensile Tests ◽  
Superior Performance ◽  
Fibre Reinforced Concrete ◽  
Marine Fauna ◽  
Recycled Pet ◽  
Pet Bottles ◽  
Fibre Aspect Ratio

Discarded polyethylene terephthalate (PET) bottles have damaged our ecosystem. Problems of marine fauna conservation and land fertility have been related to the disposal of these materials. Recycled fibre is an opportunity to reduce the levels of waste in the world and increase the mechanical performance of the concrete. PET as concrete reinforcement has demonstrated ductility and post-cracking strength. However, its performance could be optimized. This study considers a statistical-experimental analysis to evaluate recycled PET fibre reinforced concrete with various fibre dose and aspect ratio. 120 samples were experimented under workability, compressive, flexural, and splitting tensile tests. The results pointed out that the fibre dose has more influence on the responses than its fibre aspect ratio, with statistical relation on the tensional toughness, equivalent flexural strength ratio, volumetric weight, and the number of fibres. Moreover, the fibre aspect ratio has a statistical impact on the tensional toughness. In general, the data indicates that the optimal recycled PET fibre reinforced concrete generates a superior performance than control samples, with an improvement similar to those reinforced with virgin fibres.

Effect of toughened polyamide-coated carbon fiber fabric on the mechanical performance and fracture toughness of CFRP

2021 ◽  
pp. 002199832199945
Author(s):  
Jong H Eun ◽  
Bo K Choi ◽  
Sun M Sung ◽  
Min S Kim ◽  
Joon S Lee
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Photoelectron Spectroscopy ◽  
Mechanical Performance ◽  
Epoxy Composites ◽  
Scanning Calorimetry ◽  
Internal Damage ◽  
Impact Tests ◽  
Flexural Tests ◽  
The Impact

In this study, carbon/epoxy composites were manufactured by coating with a polyamide at different weight percentages (5 wt.%, 10 wt.%, 15 wt.%, and 20 wt.%) to improve their impact resistance and fracture toughness. The chemical reaction between the polyamide and epoxy resin were examined by fourier transform infrared spectroscopy, differential scanning calorimetry and X-ray photoelectron spectroscopy. The mechanical properties and fracture toughness of the carbon/epoxy composites were analyzed. The mechanical properties of the carbon/epoxy composites, such as transverse flexural tests, longitudinal flexural tests, and impact tests, were investigated. After the impact tests, an ultrasonic C-scan was performed to reveal the internal damage area. The interlaminar fracture toughness of the carbon/epoxy composites was measured using a mode I test. The critical energy release rates were increased by 77% compared to the virgin carbon/epoxy composites. The surface morphology of the fractured surface was observed. The toughening mechanism of the carbon/epoxy composites was suggested based on the confirmed experimental data.

scholarly journals Metallization of Thermoplastic Polymers and Composites 3D Printed by Fused Filament Fabrication

Technologies ◽  
2021 ◽  
Vol 9 (3) ◽  
pp. 49
Author(s):  
Alessia Romani ◽  
Andrea Mantelli ◽  
Paolo Tralli ◽  
Stefano Turri ◽  
Marinella Levi ◽  
...  
Keyword(s):  
Physical Vapor Deposition ◽  
Test Sample ◽  
Tensile Tests ◽  
Layer By Layer ◽  
Post Processing ◽  
Thermoplastic Polymers ◽  
Fused Filament Fabrication ◽  
Scanning Calorimetry ◽  
3D Printed ◽  
Manufacturing Technologies

Fused filament fabrication allows the direct manufacturing of customized and complex products although the layer-by-layer appearance of this process strongly affects the surface quality of the final parts. In recent years, an increasing number of post-processing treatments has been developed for the most used materials. Contrarily to other additive manufacturing technologies, metallization is not a common surface treatment for this process despite the increasing range of high-performing 3D printable materials. The objective of this work is to explore the use of physical vapor deposition sputtering for the chromium metallization of thermoplastic polymers and composites obtained by fused filament fabrication. The thermal and mechanical properties of five materials were firstly evaluated by means of differential scanning calorimetry and tensile tests. Meanwhile, a specific finishing torture test sample was designed and 3D printed to perform the metallization process and evaluate the finishing on different geometrical features. Furthermore, the roughness of the samples was measured before and after the metallization, and a cost analysis was performed to assess the cost-efficiency. To sum up, the metallization of five samples made with different materials was successfully achieved. Although some 3D printing defects worsened after the post-processing treatment, good homogeneity on the finest details was reached. These promising results may encourage further experimentations as well as the development of new applications, i.e., for the automotive and furniture fields.

scholarly journals Mechanical and thermal stability of retained austenite in plastically deformed bainite-based TRIP-aided medium-Mn steels

2021 ◽  
Vol 21 (3) ◽  
Author(s):  
Aleksandra Kozłowska ◽  
Adam Grajcar ◽  
Aleksandra Janik ◽  
Krzysztof Radwański ◽  
Ulrich Krupp ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Thermal Stability ◽  
Retained Austenite ◽  
Elevated Temperatures ◽  
Mechanical Performance ◽  
Mechanical Stability ◽  
Electron Backscatter Diffraction ◽  
Cost Effective ◽  
Tensile Tests ◽  
Thermal Stability Of

AbstractAdvanced medium-Mn sheet steels show an opportunity for the development of cost-effective and light-weight automotive parts with improved safety and optimized environmental performance. These steels utilize the strain-induced martensitic transformation of metastable retained austenite to improve the strength–ductility balance. The improvement of mechanical performance is related to the tailored thermal and mechanical stabilities of retained austenite. The mechanical stability of retained austenite was estimated in static tensile tests over a wide temperature range from 20 °C to 200 °C. The thermal stability of retained austenite during heating at elevated temperatures was assessed by means of dilatometry. The phase composition and microstructure evolution were investigated by means of scanning electron microscopy, electron backscatter diffraction, X-ray diffraction and transmission electron microscopy techniques. It was shown that the retained austenite stability shows a pronounced temperature dependence and is also stimulated by the manganese addition in a 3–5% range.

Sign in / Sign up

Export Citation Format

Share Document