Quantification of Fluid Production Distribution in Deviated Wells with High Gas-Liquid Ratio Using a Flow Array Sensing Tool

2021 ◽  
Author(s):  
José Wilfredo González ◽  
Alejandro Jose Linares ◽  
Diego Armando Rodriguez ◽  
Gerson Orlando Rivera ◽  
Virginie M. Schoepf ◽  
...  
Keyword(s):  
Flow Pattern ◽  
Oil And Gas ◽  
Phase Segregation ◽  
Optical Probes ◽  
High Side ◽  
Three Phase ◽  
Wide Range ◽  
Heavy Phase ◽  
Array Sensing ◽  
Deviated Wells

Abstract The objective of this paper is to depict the quantification of the production rates of the different phases in deviated wells with high gas-liquid relation using the Flow Array Sensing Tool (FAST). The readings of standard Production Logging Tools (fullbore flowmeter, density, and capacitance) are centralized, therefore they are affected if there is re-circulation of the heavy phase (liquid). The phase segregation and possible apparent down flow of the heavy phase makes it very difficult to determine the distribution of the produced fluids, and in some cases the spinner flowmeter tends to stop or gives inaccurate readings. The cause of these inaccurate readings is that the centralized spinner is affected by positive flow in the high side and negative flow in the low side of the wellbore, and the spinner shows no flow or even apparent downhole flow, when there is a real positive flow. The FAST tool used during the acquisition of the production logs is an ultracompact production logging tool (3 ft long) that is capable to measure multiphase flows with an array of 8 sensors, two in each arm and located 90° apart. These sensors are based on MEMS (Microelectromechanichal Systems), and among the interchangeable sensors we have optical probes that takes ultra-rapid measurements of the refractive index and can determine hold-up of water, oil and gas; the electrical probes that measures conductivity to differentiate hydrocarbons from water, and magnetic probes with micro-spinners to determine the flow rate. Both the three phase optical probes and the electrical probes have excellent response including water hold-ups over 90% that cannot be measured with a standard capacitance tool. The data logged with FAST in deviated wells was processed and interpreted to obtain the apparent flow velocity profiles of each of the 4 micro-spinners and with the three phase optical probes, and the relative bearing curves the velocity maps, and hold-up maps where obtained. The velocity map showed that there was negative flow in the low side of the well and positive flow in the high side while the hold-up map showed the light phase (gas) in the high side of the well. Both maps showed clearly the flow pattern and were used to quantify the production of each perforation and the total rate matched closely the surface rate (within 2% deviation). With the hold-up and velocity maps, the real flow rates were obtained with high confidence, and the flow pattern were shown clearly in deviated wells. The three phase optical probes, and electrical probes are excellent indicators of water and hydrocarbons inflow in a wide range of hold-ups.

scholarly journals Quadrature Voltage Compensation in the Isolated Multi-Modular Converter

Energies ◽  
2021 ◽  
Vol 14 (3) ◽  
pp. 529
Author(s):  
Cristian Verdugo ◽  
Jose Ignacio Candela ◽  
Pedro Rodriguez
Keyword(s):  
Control Strategy ◽  
Phase Voltage ◽  
Multilevel Converters ◽  
Photovoltaic Panels ◽  
Circulating Current ◽  
Three Phase ◽  
Voltage Compensation ◽  
Wide Range ◽  
Modular Converter ◽  
The Impact

Series connections of modules in cascaded multilevel converters are prone to power imbalances due to voltage differences on their DC side. When modules are connected to direct current (DC) sources, such as photovoltaic panels, the capability of withstanding power imbalances is crucial for generating the maximum power. In order to provide a possible solution for this requirement, this paper proposes a control strategy called Quadrature Voltage Compensation, which allows a wide range of power imbalances. The proposed control strategy regulates the power by introducing a circulating current between the arms and a phase angle in the output voltage. The impact of the circulating current and its effect on the phase voltage are studied. To highlight the features of the proposed strategy, an analytical model based on vector superposition is also described, demonstrating the strong capability of tolerating power differences. Finally, to validate the effectiveness of the Quadrature Voltage Compensation, simulation and experimental results are presented for a three-phase isolated multi-modular converter.

Experimental Investigation of Subsonic Turbulent Flow Over Single and Double Backward Facing Steps

1962 ◽  
Vol 84 (3) ◽  
pp. 317-325 ◽  
Author(s):  
D. E. Abbott ◽  
S. J. Kline
Keyword(s):  
Experimental Investigation ◽  
Velocity Profile ◽  
Flow Pattern ◽  
Reynolds Numbers ◽  
Area Ratio ◽  
Single Step ◽  
Reattachment Length ◽  
Double Step ◽  
Wide Range ◽  
Geometric Variables

Results are presented for flow patterns over backward facing steps covering a wide range of geometric variables. Velocity profile measurements are given for both single and double steps. The stall region is shown to consist of a complex pattern involving three distinct regions. The double step contains an assymmetry for large expansions, but approaches the single-step configuration with symmetric stall regions for small values of area ratio. No effect on flow pattern or reattachment length is found for a wide range of Reynolds numbers and turbulence intensities, provided the flow is fully turbulent before the step.

Study the effect of casting temperature on details from thermo-plastic materials

2020 ◽  
pp. 42-45
Author(s):  
J.A. Kerimov ◽  
Keyword(s):  
Oil And Gas ◽  
Oil And Gas Industry ◽  
Mold Temperature ◽  
Quality Parameters ◽  
Oil Field ◽  
Casting Temperature ◽  
Gas Industry ◽  
Field Equipment ◽  
Wide Range ◽  
The Impact

The implementation of plastic details in various constructions enables to reduce the prime cost and labor intensity of machine and device manufacturing, decrease the weight of design and improve their quality and reliability at the same time. The studies were carried out with the aim of labor productivity increase and substitution of colored and black metals with plastic masses. For this purpose, the details with certain characteristics were selected for further implementation of developed technological process in oil-gas industry. The paper investigates the impact of cylinder and compression mold temperature on the quality parameters (shrinkage and hardness) of plastic details in oil-field equipment. The accessible boundaries of quality indicators of the details operated in the equipment of exploration, drilling and exploitation of oil and gas industry are studied in a wide range of mode parameters. The mathematic dependences between quality parameters (shrinkage and hardness) of the details on casting temperature are specified.

Nanoemulsions: A Versatile Technology for Oil and Gas Applications

2021 ◽  
Author(s):  
Nouf AlJabri ◽  
Nan Shi
Keyword(s):  
Droplet Size ◽  
Large Scale ◽  
Oil And Gas ◽  
Volume Fraction ◽  
Oil Industry ◽  
Oil And Gas Industry ◽  
High Energy ◽  
Small Droplet ◽  
Gas Industry ◽  
Wide Range

Abstract Nanoemulsions (NEs) are kinetically stable emulsions with droplet size on the order of 100 nm. Many unique properties of NEs, such as stability and rheology, have attracted considerable attention in the oil industry. Here, we review applications and studies of NEs for major upstream operations, highlighting useful properties of NEs, synthesis to render these properties, and techniques to characterize them. We identify specific challenges associated with large-scale applications of NEs and directions for future studies. We first summarize useful and unique properties of NEs, mostly arising from the small droplet size. Then, we compare different methods to prepare NEs based on the magnitude of input energy, i.e., low-energy and high-energy methods. In addition, we review techniques to characterize properties of NEs, such as droplet size, volume fraction of the dispersed phase, and viscosity. Furthermore, we discuss specific applications of NEs in four areas of upstream operations, i.e., enhanced oil recovery, drilling/completion, flow assurance, and stimulation. Finally, we identify challenges to economically tailor NEs with desired properties for large-scale upstream applications and propose possible solutions to some of these challenges. NEs are kinetically stable due to their small droplet size (submicron to 100 nm). Within this size range, the rate of major destabilizing mechanisms, such as coalescence, flocculation, and Ostwald ripening, is considerably slowed down. In addition, small droplet size yields large surface-to-volume ratio, optical transparency, high diffusivity, and controllable rheology. Similar to applications in other fields (food industry, pharmaceuticals, cosmetics, etc.), the oil and gas industry can also benefit from these useful properties of NEs. Proposed functions of NEs include delivering chemicals, conditioning wellbore/reservoir conditions, and improve chemical compatibility. Therefore, we envision NEs as a versatile technology that can be applied in a variety of upstream operations. Upstream operations often target a wide range of physical and chemical conditions and are operated at different time scales. More importantly, these operations typically consume a large amount of materials. These facts not only suggest efforts to rationally engineer properties of NEs in upstream applications, but also manifest the importance to economically optimize such efforts for large-scale operations. We summarize studies and applications of NEs in upstream operations in the oil and gas industry. We review useful properties of NEs that benefit upstream applications as well as techniques to synthesize and characterize NEs. More importantly, we identify challenges and opportunities in engineering NEs for large-scale operations in different upstream applications. This work not only focuses on scientific aspects of synthesizing NEs with desired properties but also emphasizes engineering and economic consideration that is important in the oil industry.

Energy Harvesting Under Harsh Conditions for the Oil & Gas Upstream Industry

2021 ◽  
Author(s):  
José Correia ◽  
Cátia Rodrigues ◽  
Ricardo Esteves ◽  
Ricardo Cesar Bezerra de Melo ◽  
José Gutiérrez ◽  
...  
Keyword(s):  
Energy Harvesting ◽  
Oil And Gas ◽  
Electrical Energy ◽  
Development Stage ◽  
Gas Extraction ◽  
Power Monitoring ◽  
Operational Conditions ◽  
Wide Range ◽  
First Time ◽  
Harsh Conditions

Abstract Environmental and safety sensing is becoming of high importance in the oil and gas upstream industry. However, present solutions to feed theses sensors are expensive and dangerous and there is so far no technology able to generate electrical energy in the operational conditions of oil and gas extraction wells. In this paper it is presented, for the first time in a relevant environment, a pioneering energy harvesting technology based on nanomaterials that takes advantage of fluid movement in oil extraction wells. A device was tested to power monitoring systems with locally harvested energy in harsh conditions environment (pressures up to 50 bar and temperatures of 50ºC). Even though this technology is in an early development stage this work opens a wide range of possible applications in deep underwater environments and in Oil and Gas extraction wells where continuous flow conditions are present.

The Use of Controlled Dissolution Glasses to Consolidate and Create Permeable or Impermeable Minerals in Formation

2021 ◽  
Author(s):  
Max Olsen ◽  
Ragni Hatlebakk ◽  
Chris Holcroft ◽  
Arne Stavland ◽  
Nils Harald Giske ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Oil And Gas ◽  
Stable Solution ◽  
Oil And Gas Industry ◽  
Post Treatment ◽  
Strength Increase ◽  
Glass Technology ◽  
Nuclear Waste Storage ◽  
Wide Range ◽  
Glass Compositions

Abstract Scope Controlled dissolution glasses form a permanent consolidating mineral matrix inside formations with either permeable or impermeable properties. The unique solution has a low injection viscosity and can be easily injected into a wide range of formations. The application method is simple and does not require multiple fluids or pre- and post-flushing. This paper focuses on the benefits of controlled dissolution glasses and potential applications in the oil and gas industry. Methods, Procedures, Process Controlled dissolution glasses have been researched extensively by Glass Technology Services (GTS) since 1999 for the biomedical industry, nuclear waste storage industry, and defense and aerospace industries. GTS together with operators have been performing research and development for the oil industry over the last 10 years. The research investigated different glass compositions to determine their injectability and change in formation properties post-treatment. Sandstone, chalk, and shale formations were used in the testing. Flow testing using a Hoek cell and a core flood apparatus was used to determine the post-treatment permeability. For post-treatment strength measurement, Brazilian tensile strength tests and modified cone penetration tests were used to determine tensile strength and shear strength respectively. The testing evaluated different mixing fluids, such as water and different brines, compatibility, corrosion testing, and concentrations. Results, Observations, Conclusions The testing identified different glass compositions and concentrations that are suitable for different applications and formations. Certain glass compositions increase tensile strength significantly while also maintaining the permeability in the formation. Other glass compositions have similar tensile strength increase, but result in an impermeable seal. The liquid glass solutions react with the formation to form a mineral precipitation inside the formation. The reaction with the formation occurs quickly at downhole conditions, within hours of placement. The glass can be mixed with water and variety of brines to form a stable solution across a range of densities. The testing and results to date have laid the foundation for use in a variety of consolidation and P&A applications in oil and gas wells. Testing is ongoing for a chalk and sandstone consolidation solution and for a sealing solution. Novel/Additive Information These novel glass solutions can solve many of the production and instability challenges that plague weak formations. The glasses can be injected into very low permeability formation to either seal or consolidate.

A New World Economic order formation

2021 ◽  
pp. 932-950
Author(s):  
Vladislav Vyacheslavovich Emelyanov
Keyword(s):  
Oil And Gas ◽  
World Order ◽  
The United States ◽  
New Order ◽  
The West ◽  
Wide Range ◽  
The World ◽  
The Usa ◽  
World Economic Order ◽  
The Impact

Every few decades, the world order changes due to various geopolitical, economic and other circumstances. For example, as a result of globalization, the world order has undergone significant changes in the last forty years. Globalization has led to the destruction of the postwar world order, as well as to world leadership by the United States and the West. However, in recent decades, as a result of globalization, the U.S. and the West began to cede their leadership to developing countries, so there is now a change in the economic structure of relations in the world system. Today the center of economic growth is in the East, namely in Asia. There are no new superpowers in the world at the moment, but the unipolar world will cease to exist due to the weakening of the U. S. leadership, which will lead to a change in the world order. A new leader, which may replace the U. S., will not have as wide range of advantages as the USA has. Most likely, the essence of the new order will be to unite the largest countries and alliances into blocks, for example, the USA together with the Trans-Pacific Partnership, the EU, etc. The article outlines forecasts of GDP growth rates as well as the global energy outlook; analyzes the LNG market as well as the impact of the pandemic on the global oil and gas market; and lists the characteristics of U. S. geopolitics.

Activity coefficients, densities, dipole moments, and surface tensions of the system triethylamine–methylethylketone–water

1981 ◽  
Vol 59 (1) ◽  
pp. 127-131 ◽  
Author(s):  
Alan N. Campbell
Keyword(s):  
Surface Layer ◽  
Dipole Moments ◽  
Phase System ◽  
Constant Composition ◽  
Two Phase ◽  
Three Phase ◽  
Wide Range ◽  
Isothermal System ◽  
Total Composition ◽  
Two Phases

The properties named in the title have been determined by standard methods. Viscosity, molar volume, and orientation polarisation all indicate abnormalities of the nature of association between the components.The most interesting result is that of surface tension which indicates that, in the case of the binary system triethylamine–water, a surface layer of constant composition is formed over a wide range of total composition. When, by a rise in temperature of two or three degrees, this layer becomes unstable, it splits into two phases of different composition. The surface layer may then be instantaneously reformed and so on. A mechanism for the generation of a two-phase system is thus established. The data for the three-phase, isothermal, system are not so convincing, for reasons that are suggested.

scholarly journals DQ-Frame Admittance Estimation of Three-Phase Converters with a Wide Range of Operating Points

2021 ◽  
Author(s):  
Hong Gong ◽  
xiongfei wang ◽  
Dongsheng Yang
Keyword(s):  
Error Estimation ◽  
Closed Loop ◽  
Estimation Method ◽  
Experimental Results ◽  
Multidimensional Interpolation ◽  
Three Phase ◽  
Wide Range ◽  
Linearized Model ◽  
Operating Points ◽  
Error Estimation Method

The <i>dq</i>-frame admittance of closed-loop controlled three-phase converters is a linearized model that is dependent on the operating points of the system. Yet, it is impractical to measure the converter admittance at all operating points. This paper, thus, proposes an approach to estimating the <i>dq</i>-frame admittance of three-phase converters at a wide range of operating points. The method applies multidimensional interpolation to a given set of admittance data, which is measured from the pre-defined operating points. The accuracy of interpolation is then evaluated by using the posterior error estimation method. The number of pre-defined operating points is next adjusted to find a good compromise between the accuracy and efficiency of the approach. Simulations and experimental results verify the effectiveness of the approach.<div><br></div>

scholarly journals Design and Implementation of Single Stage PFC Microcontroller Based Drive For Permanent Magnet Brushless DC Motor

2013 ◽  
pp. 289-293
Author(s):  
Minal A Bodkhe ◽  
Vaishali Nandanwar
Keyword(s):  
Permanent Magnet ◽  
Power Factor ◽  
Dc Motor ◽  
Brushless Dc Motor ◽  
Brushless Dc ◽  
Three Phase ◽  
Wide Range ◽  
Sinusoidal Input ◽  
Bridge Rectifier ◽  
Permanent Magnet Brushless Dc

In this paper ,a new approach is presented aim at improving the power factor of three phase bridge inverter that equip with permanent Magnet Brushless DC motor(PMBLDCM)drive through microcontroller. Power factor correction converter is used for feeding a three phase bridge inverter based PMBLDC motor drive. The front end of PFC converter is a diode bridge rectifier fed from a step down transformer. In this three phase bridge inverter is operated as electronic commutator of the PMBLDCM .Nearly sinusoidal input current is achieved using. The proposed PMBLDCM drive with PFC converter is designed to run the motor to desired speed. This scheme improves an efficiency of proposed drive system with PFC feature in wide range of the speed and an input AC voltage.

Sign in / Sign up

Export Citation Format

Share Document